| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: firewire: isight: bound the sample count to the packet payload
isight_packet() takes the frame count from the device iso packet and
checks it only against the device claimed iso length.
count = be32_to_cpu(payload->sample_count);
if (likely(count <= (length - 16) / 4))
isight_samples(isight, payload->samples, count);
length is the iso header data_length. It can be up to 0xffff. So the
gate allows a count up to about 16379. isight_samples() then copies
count frames out of payload->samples into the PCM DMA buffer.
payload->samples holds only 2 * MAX_FRAMES_PER_PACKET values. The
device multiplexes two samples per frame. A count past
MAX_FRAMES_PER_PACKET reads past the payload. A count past the buffer
size writes past runtime->dma_area. The smallest PCM buffer is larger
than MAX_FRAMES_PER_PACKET. Bounding the count to MAX_FRAMES_PER_PACKET
keeps both the read and the write in range.
A malicious or faulty Apple iSight on the FireWire bus reaches this
during a normal capture.
Add the MAX_FRAMES_PER_PACKET bound to the gate. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: fix heap buffer overflow in rtw_cfg80211_set_wpa_ie()
supplicant_ie is a 256-byte array in struct security_priv. The WPA and
WPA2 IE copy paths use:
memcpy(padapter->securitypriv.supplicant_ie, &pwpa[0], wpa_ielen + 2);
where wpa_ielen is the raw IE length field (u8, 0-255). When a local user
supplies a connect request via nl80211 with a crafted WPA IE of length 255,
wpa_ielen + 2 equals 257, overflowing the 256-byte buffer by one byte into
the adjacent last_mic_err_time field.
rtw_parse_wpa_ie() does not prevent this: its length consistency check
compares *(wpa_ie+1) against (u8)(wpa_ie_len-2), which is (u8)(255) == 255
when wpa_ie_len = 257, so the check passes silently.
Add explicit bounds checks for both the WPA and WPA2 paths before the
memcpy, rejecting any IE whose total size (wpa_ielen + 2) exceeds the
supplicant_ie buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: bound RX frame length in kalmia_rx_fixup()
kalmia_rx_fixup() computes usb_packet_length = skb->len - (2 *
KALMIA_HEADER_LENGTH) as a u16, guarded only by a pre-loop check that
skb->len is at least KALMIA_HEADER_LENGTH, which is 6. A device can
deliver a short bulk-IN frame with skb->len in the 6 to 11 range, or
leave a short trailing remainder on a later loop iteration. Either case
underflows usb_packet_length to about 65530.
That bypasses the usb_packet_length < ether_packet_length truncation path.
The device-supplied ether_packet_length, a le16 up to 65535 read from
header_start[2], then drives a memcmp() and the following skb_trim() and
skb_pull() past the end of the rx buffer. The rx buffer is hard_mtu * 10,
which is 14000 bytes. That is an out of bounds read.
Require both the start and end framing headers to be present before
subtracting them, on every loop iteration. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix dead empty check in the USB_DT_OTG handler
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm: Validate SVID index in svdm_consume_modes()
In svdm_consume_modes(), the SVID value is read from pmdata->svids using
pmdata->svid_index as an array index without bounds validation:
paltmode->svid = pmdata->svids[pmdata->svid_index];
If pmdata->svid_index is driven beyond SVID_DISCOVERY_MAX (16), it results
in an out-of-bounds read of the pmdata->svids array. Because pd_mode_data
is embedded inside struct tcpm_port, indexing past svids reads into
adjacent fields. In particular:
- At index 16, it reads the altmodes count.
- At index 18 and beyond, it reads into altmode_desc[], which contains
partner-supplied SVDM Discovery Modes VDOs.
By injecting a chosen SVID into altmode_desc[0].vdo and driving svid_index
to 20, the partner can force paltmode->svid to be loaded with an arbitrary,
partner- chosen SVID, which is then registered via
typec_partner_register_altmode().
Fix this by validating that pmdata->svid_index is non-negative and strictly
less than pmdata->nsvids before accessing the pmdata->svids array inside
svdm_consume_modes(). |
| In the Linux kernel, the following vulnerability has been resolved:
Input: mms114 - fix touch indexing for MMS134S and MMS136
The MMS134S and MMS136 touch controllers have an event size of 6 bytes
rather than 8 bytes. When __mms114_read_reg() reads the touch data
packet from the device into the touch buffer, the events are packed
tightly at 6-byte intervals. However, the driver iterates through the
events using standard C array indexing (touch[index]), where each
element is sizeof(struct mms114_touch) (8 bytes) apart. As a result, any
touch events beyond the first one are read from incorrect offsets and
parsed improperly.
Fix this by explicitly calculating the byte offset for each touch event
based on the device's specific event size. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: touchwin - reset the packet index on every complete packet
tw_interrupt() accumulates each non-zero serial byte into a fixed
three-byte buffer with a running index that is only reset once a full
packet has been received *and* the device's two Y bytes agree:
tw->data[tw->idx++] = data;
if (tw->idx == TW_LENGTH && tw->data[1] == tw->data[2]) {
...
tw->idx = 0;
}
The reset is gated on tw->data[1] == tw->data[2], a value the device
controls. A malicious, malfunctioning or counterfeit Touchwindow
peripheral can stream non-zero bytes whose 2nd and 3rd bytes differ: the
index reaches TW_LENGTH without the equality holding, is never reset, and
keeps growing, so tw->data[tw->idx++] walks off the end of the three-byte
array and the rest of the heap-allocated struct tw, one attacker-chosen
byte at a time -- an unbounded, device-driven heap out-of-bounds write.
Reset the index on every completed packet and report an event only when
the two Y bytes match, like the other serio touchscreen drivers do. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: elan_i2c - validate firmware size before use
Ensure that the firmware file is large enough to contain the expected
number of pages and the signature (which resides at the end of the
firmware blob) before accessing them to prevent potential out-of-bounds
reads. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: CGX: add bounds check to cgx_speed_mbps index
cgx_speed_mbps has 13 elements but RESP_LINKSTAT_SPEED can yield values
0-15. If it returns a value >= 13, this causes an out-of-bounds array
access. Add a bounds check and default to speed 0 if the index is out of
range. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Remove latent out-of-bounds access in IOMMU debugfs
In iommu_mmio_write() and iommu_capability_write(), the variables
dbg_mmio_offset and dbg_cap_offset are declared as int. However, they
are populated using kstrtou32_from_user(). If a user provides a
sufficiently large value, it can become a negative integer.
Prior to this patch, the AMD IOMMU debugfs implementation was already
protected by different mechanisms.
1. #define OFS_IN_SZ 8 ensures the user string <= 8 bytes, so
e.g. 0xffffffff isn't a valid input.
if (cnt > OFS_IN_SZ)
return -EINVAL;
2. Implicit type promotion in iommu_mmio_write(), dbg_mmio_offset is int
and iommu->mmio_phys_end is u64
if (dbg_mmio_offset > iommu->mmio_phys_end - sizeof(u64))
return -EINVAL;
3. The show handlers would currently catch the negative number and
refuse to perform the read.
Replace kstrtou32_from_user() with kstrtos32_from_user() to parse the
input, and check for negative values to explicitly prevent out-of-bounds
memory accesses directly in iommu_mmio_write() and
iommu_capability_write(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: ifb: report ethtool stats over num_tx_queues
ifb_dev_init() allocates dp->tx_private to dev->num_tx_queues
entries via kzalloc_objs(*txp, dev->num_tx_queues). Both IFB
per-queue RX and TX stats live in those entries: ifb_xmit() updates
txp->rx_stats using the skb queue mapping, ifb_ri_tasklet() updates
txp->tx_stats, and ifb_stats64() aggregates both over
dev->num_tx_queues.
The ethtool stats callbacks instead size and walk the per-queue
stats with dev->real_num_rx_queues and dev->real_num_tx_queues. With
an asymmetric device where the RX queue count exceeds the TX queue
count, for example:
ip link add name ifb10 numtxqueues 1 numrxqueues 8 type ifb
ethtool -S ifb10
ifb_get_ethtool_stats() indexes past the tx_private allocation and
copies adjacent slab data through ETHTOOL_GSTATS.
Use dev->num_tx_queues consistently for the stats strings, the
stats count, and the stats data walks. This reports one RX stats
group and one TX stats group for each backing ifb_q_private entry,
which is the queue set IFB can actually populate.
Reproduced under UML+KASAN at v7.1-rc2:
BUG: KASAN: slab-out-of-bounds in ifb_fill_stats_data+0x3c/0xae
Read of size 8 at addr 0000000062dbd228 by task ethtool/36
ifb_fill_stats_data+0x3c/0xae
ifb_get_ethtool_stats+0xc0/0x129
__dev_ethtool+0x1ca5/0x363c
dev_ethtool+0x123/0x1b3
dev_ioctl+0x56c/0x744
sock_do_ioctl+0x15f/0x1b2
sock_ioctl+0x4d5/0x50a
sys_ioctl+0xd8b/0xde9
With the patch applied, the same UML+KASAN repro is silent and
ethtool -S ifb10 reports only the stats backed by the single
allocated tx_private entry. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: Add upper bound check for num_of_nodes
drm/amdkfd: Add upper bound check for num_of_nodes
in kfd_ioctl_get_process_apertures_new.
(cherry picked from commit 98ff46a5ea090c14d2cdb4f5b993b05d74f3949f) |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: Place upper limit on station AID
Any station configured with an AID over 20 causes a firmware crash.
This situation occurred in our testing using an AP interface on 7922
hardware, with a modified hostapd, sourced from Mediatek's OpenWRT
feeds.
In stock hostapd, station AIDs begin counting at 1, and this
configuration is prevented with an upper limit on associated stations.
However, the modified hostapd began allocation at 65, which caused the
firmware to crash. This fix does not allow these AIDs to work, but will
prevent the firmware crash.
This crash was only seen on IFTYPE_AP interfaces, and the fix does not
appear to have an effect on IFTYPE_STATION behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sg: Resolve soft lockup issue when opening /dev/sgX
The parameter def_reserved_size defines the default buffer size reserved
for each Sg_fd and should be restricted to a range between 0 and 1,048,576
(see https://tldp.org/HOWTO/SCSI-Generic-HOWTO/proc.html). Although the
function sg_proc_write_dressz enforces this limit, it is possible to bypass
it by directly modifying the module parameter as shown below, which then
causes a soft lockup:
echo -1 > /sys/module/sg/parameters/def_reserved_size
exec 4<> /dev/sg0
watchdog: BUG: soft lockup - CPU#5 stuck for 26 seconds! [bash:537]
Modules loaded:
CPU: 5 UID: 0 PID: 537 Command: bash, kernel version 6.19.0-rc3+ #134,
PREEMPT disabled
Hardware: QEMU Standard PC (i440FX + PIIX, 1996), BIOS version
1.16.1-2.fc37 dated 04/01/2014
...
Call Trace:
sg_build_reserve+0x5c/0xa0
sg_add_sfp+0x168/0x270
sg_open+0x16e/0x340
chrdev_open+0xbe/0x230
do_dentry_open+0x175/0x480
vfs_open+0x34/0xf0
do_open+0x265/0x3d0
path_openat+0x110/0x290
do_filp_open+0xc3/0x170
do_sys_openat2+0x71/0xe0
__x64_sys_openat+0x6d/0xa0
do_syscall_64+0x62/0x310
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The fix is to use module_param_cb to validate and reject invalid values
assigned to def_reserved_size. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/amd: Bounds-check devid in __rlookup_amd_iommu()
iommu_device_register() walks every device on the PCI bus via
bus_for_each_dev() and calls amd_iommu_probe_device() for each. The
inlined check_device() path computes the device's sbdf, calls
rlookup_amd_iommu() to find the owning IOMMU, and only afterwards
verifies devid <= pci_seg->last_bdf. __rlookup_amd_iommu() indexes
rlookup_table[devid] with no bounds check of its own, so for a PCI
device whose BDF is not described by the IVRS, the lookup reads past
the end of the allocation before the caller's bounds check can run.
This was harmless before commit e874c666b15b ("iommu/amd: Change
rlookup, irq_lookup, and alias to use kvalloc()"): the table was a
zeroed page-order allocation, so the over-read returned NULL and the
caller's NULL check skipped the device. After that commit the table is
a tight kvcalloc() and the over-read returns adjacent slab contents,
which check_device() then dereferences as a struct amd_iommu *,
causing a boot-time GPF.
Seen on Google Compute Engine ct6e VMs, where the virtualized IVRS
describes only the four TPU endpoints 00:04.0-07.0; the gVNIC at
00:08.0 (devid 0x40) indexes 56 bytes past the 456-byte allocation,
into the adjacent kmalloc-512 slab object:
pci 0000:00:04.0: Adding to iommu group 0
pci 0000:00:05.0: Adding to iommu group 1
pci 0000:00:06.0: Adding to iommu group 2
pci 0000:00:07.0: Adding to iommu group 3
Oops: general protection fault, probably for non-canonical address 0x3a64695f78746382: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Not tainted 6.18.22 #1
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 12/06/2025
RIP: 0010:amd_iommu_probe_device+0x54/0x3a0
Call Trace:
__iommu_probe_device+0x107/0x520
probe_iommu_group+0x29/0x50
bus_for_each_dev+0x7e/0xe0
iommu_device_register+0xc9/0x240
iommu_go_to_state+0x9c0/0x1c60
amd_iommu_init+0x14/0x40
pci_iommu_init+0x16/0x60
do_one_initcall+0x47/0x2f0
Guard the array access in __rlookup_amd_iommu(). With the fix applied
on 6.18.22, the gVNIC at 00:08.0 is skipped cleanly and the VM boots. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: MGMT: validate advertising TLV before type checks
tlv_data_is_valid() reads each advertising data field length from
data[i], then inspects data[i + 1] for managed EIR types before
checking that the current field still fits inside the supplied buffer.
A malformed field whose length byte is the last byte of the buffer can
therefore make the parser read one byte past the advertising data.
KASAN reported the following when a malformed MGMT_OP_ADD_ADVERTISING
request reached that path:
BUG: KASAN: vmalloc-out-of-bounds in tlv_data_is_valid()
Read of size 1
Call trace:
tlv_data_is_valid()
add_advertising()
hci_mgmt_cmd()
hci_sock_sendmsg()
Move the existing element-length check before any type-octet inspection
so each non-empty element is proven to contain its type byte before the
parser looks at data[i + 1]. |
| In the Linux kernel, the following vulnerability has been resolved:
net/802/mrp: fix vector attribute parsing in mrp_pdu_parse_vecattr
In mrp_pdu_parse_vecattr(), vector attribute events are encoded three
per byte and valen tracks the number of events left to process.
The parser decrements valen after processing the first and second events
from each event byte, but not after processing the third one. When valen
is exactly a multiple of three, the loop continues after the last valid
event and consumes the next byte as a new event byte, applying a
spurious event to the MRP applicant state.
Additionally, when valen is zero the parser unconditionally consumes
attrlen bytes as FirstValue and advances the offset, even though per
IEEE 802.1ak a VectorAttribute with only a LeaveAllEvent has valen of
zero and no FirstValue or Vector fields. This corrupts the offset for
subsequent PDU parsing.
Also, when valen exceeds three the loop crosses byte boundaries but
the attribute value is not incremented between the last event of one
byte and the first event of the next. This causes the first event of
the next byte to use the same attribute value as the third event
rather than the next consecutive value.
Decrement valen after processing the third event, skip FirstValue
consumption when valen is zero, and increment the attribute value at
the end of each loop iteration. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: dummy: fix UMP event stack overread
The dummy sequencer port forwards events by copying an incoming
struct snd_seq_event into a stack temporary, rewriting source and
destination, and dispatching the temporary to subscribers. That legacy
event storage is smaller than struct snd_seq_ump_event.
When a UMP event reaches the dummy client, the copy leaves the UMP flag
set but only provides legacy-sized stack storage. The subscriber
delivery path then uses snd_seq_event_packet_size() and copies a
UMP-sized packet from that stack object, reading past the end of the
temporary.
Use the existing union __snd_seq_event storage and copy the packet size
reported for the incoming event before rewriting the common routing
fields. This preserves the full UMP packet for UMP events while keeping
legacy event handling unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
netlabel: validate unlabeled address and mask attribute lengths
netlbl_unlabel_addrinfo_get() used the address attribute length to
determine whether the attribute data could be read as an IPv4 or IPv6
address, but did not independently validate the corresponding mask
attribute length. A crafted Generic Netlink request could therefore
provide a valid IPv4/IPv6 address attribute with a shorter mask
attribute, which would later be read as a full struct in_addr or
struct in6_addr.
NLA_BINARY policy lengths are maximum lengths by default, so use
NLA_POLICY_EXACT_LEN() for the unlabeled IPv4/IPv6 address and mask
attributes. This rejects short attributes during policy validation and
also exposes the exact length requirements through policy introspection. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: L2CAP: reject BR/EDR signaling packets over MTUsig
net/bluetooth/l2cap_core.c:l2cap_sig_channel() accepts BR/EDR
signaling packets up to the channel MTU and dispatches each command
without enforcing the signaling MTU (MTUsig). A Bluetooth BR/EDR peer
within radio range can send a fixed-channel CID 0x0001 packet that is
larger than MTUsig and contains many L2CAP_ECHO_REQ commands before
pairing. In a real-radio stock-kernel run, one 681-byte signaling
packet containing 168 zero-length ECHO_REQ commands made the target
transmit 168 ECHO_RSP frames over about 220 ms.
Impact: a Bluetooth BR/EDR peer within radio range, before pairing, can
force 168 ECHO_RSP frames from one 681-byte fixed-channel signaling
packet containing packed ECHO_REQ commands.
Define Linux's BR/EDR signaling MTU as the spec minimum of 48 bytes and
reject any larger signaling packet with one L2CAP_COMMAND_REJECT_RSP
carrying L2CAP_REJ_MTU_EXCEEDED before any command is dispatched.
The Bluetooth Core spec wording for MTUExceeded says the reject
identifier shall match the first request command in the packet, and
that packets containing only responses shall be silently discarded.
Linux intentionally deviates from that prescription: silently
discarding desynchronizes the peer because the remote stack never
learns its responses were dropped, and locating the first request
command requires walking command headers past MTUsig, i.e. processing
bytes from a packet we have already decided is too large to process.
We therefore always emit one reject and use the identifier from the
first command header, a single fixed-offset byte read.
The unrestricted BR/EDR signaling parser and ECHO_REQ response path both
trace to the initial git import; no later introducing commit is
available for a Fixes tag. |
