| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Stack buffer overflow vulnerability in D-Link DIR-513 v1.10 via the webPage parameter to goform/formWlanGuestSetup. |
| An issue was discovered in DIR-823 firmware 20250416. There is an RCE vulnerability in the set_cassword settings interface, as the http_casswd parameter is not filtered by '&'to allow injection of reverse connection commands. |
| D-Link Router DIR-868L A1 FW106KRb01.bin has an unauthenticated remote code execution vulnerability in the cgibin binary. The HNAP service provided by cgibin does not filter the HTTP SOAPAction header field. The unauthenticated remote attacker can execute the shell command. |
| A command injection vulnerability exists in the D-Link DIR-823G router firmware DIR823G_V1.0.2B05_20181207.bin in the timelycheck and sysconf binaries, which process the /tmp/new_qos.rule configuration file. The vulnerability occurs because parsed fields from the configuration file are concatenated into command strings and executed via system() without any sanitization. An attacker with write access to /tmp/new_qos.rule can execute arbitrary commands on the device. |
| A command injection vulnerability exists in the D-Link DIR-823G router firmware DIR823G_V1.0.2B05_20181207.bin in the timelycheck and sysconf binaries, which process the /var/system/linux_vlan_reinit file. The vulnerability occurs because content read from this file is only partially validated for a prefix and then formatted using vsnprintf() before being executed with system(), allowing an attacker with write access to /var/system/linux_vlan_reinit to execute arbitrary commands on the device. |
| A stack buffer overflow vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin in the rc binary's USB storage handling module. The vulnerability occurs when the "Serial Number" field from a USB device is read via sscanf into a 64-byte stack buffer, while fgets reads up to 127 bytes, causing a stack overflow. An attacker with physical access or control over a USB device can exploit this vulnerability to potentially execute arbitrary code on the device. |
| An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetDynamicDNSSettings' functionality, where the 'ServerAddress' and 'Hostname' parameters in prog.cgi are stored in NVRAM and later used by rc to construct system commands executed via twsystem(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device. |
| An unauthenticated command injection vulnerability exists in the D-Link DIR-878A1 router firmware FW101B04.bin. The vulnerability occurs in the 'SetDMZSettings' functionality, where the 'IPAddress' parameter in prog.cgi is stored in NVRAM and later used by librcm.so to construct iptables commands executed via twsystem(). An attacker can exploit this vulnerability remotely without authentication by sending a specially crafted HTTP request, leading to arbitrary command execution on the device. |
| A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_4438A4` function in `prog.cgi` stores user-supplied DDNS parameters (`ServerAddress` and `Hostname`) in NVRAM via `nvram_safe_set`. These values are later retrieved in the `start_DDNS_ipv4` function of `rc` using `nvram_safe_get` and concatenated into DDNS shell commands executed via `twsystem()` without proper sanitization. Partial string comparison is performed but is insufficient to prevent command injection. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface. |
| A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_432F60` function in `prog.cgi` stores user-supplied `SetSysLogSettings/IPAddress` values in NVRAM via `nvram_safe_set("SysLogRemote_IPAddress", ...)`. These values are later retrieved in the `sub_448DCC` function of `rc` using `nvram_safe_get` and concatenated into a shell command executed via `twsystem()` without any sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface. |
| A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `librcm.so` binaries. The `sub_4455BC` function in `prog.cgi` stores user-supplied `SetDMZSettings/IPAddress` values in NVRAM via `nvram_safe_set("dmz_ipaddr", ...)`. These values are later retrieved in the `DMZ_run` function of `librcm.so` using `nvram_safe_get` and concatenated into `iptables` shell commands executed via `twsystem()` without any sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface. |
| A command injection vulnerability exists in the D-Link DIR-882 Router firmware DIR882A1_FW102B02 within the `prog.cgi` and `rc` binaries. The `sub_433188` function in `prog.cgi` stores user-supplied email configuration parameters (`EmailFrom`, `EmailTo`, `SMTPServerAddress`, `SMTPServerPort`, `AccountName`) in NVRAM via `nvram_safe_set`. These values are later retrieved in the `sub_448FDC` function of `rc` using `nvram_safe_get` and concatenated into shell commands executed via `twsystem()` without sanitization. An unauthenticated remote attacker can exploit this vulnerability to execute arbitrary commands on the device through specially crafted HTTP requests to the router's web interface. |
| D-Link DIR-610 devices allow Remote Command Execution via the cmd parameter to command.php. NOTE: This vulnerability only affects products that are no longer supported by the maintainer |
| D-Link DNS-320 FW v2.06B01 Revision Ax is affected by command injection in the system_mgr.cgi component, which can lead to remote arbitrary code execution. |
| An issue was discovered on D-Link DIR-825 R1 devices through 3.0.1 before 2020-11-20. A buffer overflow in the web interface allows attackers to achieve pre-authentication remote code execution. |
| An issue was discovered on D-Link DCS-2530L before 1.06.01 Hotfix and DCS-2670L through 2.02 devices. The unauthenticated /config/getuser endpoint allows for remote administrator password disclosure. |
| An issue was discovered on D-Link DCS-2530L before 1.06.01 Hotfix and DCS-2670L through 2.02 devices. cgi-bin/ddns_enc.cgi allows authenticated command injection. |
| Unauthenticated remote code execution occurs in D-Link products such as DIR-655C, DIR-866L, DIR-652, and DHP-1565. The issue occurs when the attacker sends an arbitrary input to a "PingTest" device common gateway interface that could lead to common injection. An attacker who successfully triggers the command injection could achieve full system compromise. Later, it was independently found that these are also affected: DIR-855L, DAP-1533, DIR-862L, DIR-615, DIR-835, and DIR-825. |
| The UPnP endpoint URL /gena.cgi in the D-Link DIR-859 Wi-Fi router 1.05 and 1.06B01 Beta01 allows an Unauthenticated remote attacker to execute system commands as root, by sending a specially crafted HTTP SUBSCRIBE request to the UPnP service when connecting to the local network. |
| D-Link DWL-2600AP 4.2.0.15 Rev A devices have an authenticated OS command injection vulnerability via the Save Configuration functionality in the Web interface, using shell metacharacters in the admin.cgi?action=config_save configBackup or downloadServerip parameter. |
