| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/osnoise: Call synchronize_rcu() when unregistering
This ensures that any RCU readers traversing the instance list
have finished, before releasing the reference on the tracer that
the instance points to. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet-tcp: check INIT_FAILED before nvmet_req_uninit in digest error path
In nvmet_tcp_try_recv_ddgst(), when a data digest mismatch is detected,
nvmet_req_uninit() is called unconditionally. However, if the command
arrived via the nvmet_tcp_handle_req_failure() path, nvmet_req_init()
had returned false and percpu_ref_tryget_live() was never executed. The
unconditional percpu_ref_put() inside nvmet_req_uninit() then causes a
refcount underflow, leading to a WARNING in
percpu_ref_switch_to_atomic_rcu, a use-after-free diagnostic, and
eventually a permanent workqueue deadlock.
Check cmd->flags & NVMET_TCP_F_INIT_FAILED before calling
nvmet_req_uninit(), matching the existing pattern in
nvmet_tcp_execute_request(). |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid5: fix soft lockup in retry_aligned_read()
When retry_aligned_read() encounters an overlapped stripe, it releases
the stripe via raid5_release_stripe() which puts it on the lockless
released_stripes llist. In the next raid5d loop iteration,
release_stripe_list() drains the stripe onto handle_list (since
STRIPE_HANDLE is set by the original IO), but retry_aligned_read()
runs before handle_active_stripes() and removes the stripe from
handle_list via find_get_stripe() -> list_del_init(). This prevents
handle_stripe() from ever processing the stripe to resolve the
overlap, causing an infinite loop and soft lockup.
Fix this by using __release_stripe() with temp_inactive_list instead
of raid5_release_stripe() in the failure path, so the stripe does not
go through the released_stripes llist. This allows raid5d to break out
of its loop, and the overlap will be resolved when the stripe is
eventually processed by handle_stripe(). |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix deadlock with check operation and nowait requests
When an array check is running it will raise the barrier at which point
normal requests will become blocked and increment the nr_pending value to
signal there is work pending inside of wait_barrier(). NOWAIT requests
do not block and so will return immediately with an error, and additionally
do not increment nr_pending in wait_barrier(). Upstream change commit
43806c3d5b9b ("raid10: cleanup memleak at raid10_make_request") added a
call to raid_end_bio_io() to fix a memory leak when NOWAIT requests hit
this condition. raid_end_bio_io() eventually calls allow_barrier() and
it will unconditionally do an atomic_dec_and_test(&conf->nr_pending) even
though the corresponding increment on nr_pending didn't happen in the
NOWAIT case.
This can be easily seen by starting a check operation while an application
is doing nowait IO on the same array. This results in a deadlocked state
due to nr_pending value underflowing and so the md resync thread gets stuck
waiting for nr_pending to == 0.
Output of r10conf state of the array when we hit this condition:
crash> struct r10conf
barrier = 1,
nr_pending = {
counter = -41
},
nr_waiting = 15,
nr_queued = 0,
Example of md_sync thread stuck waiting on raise_barrier() and other
requests stuck in wait_barrier():
md1_resync
[<0>] raise_barrier+0xce/0x1c0
[<0>] raid10_sync_request+0x1ca/0x1ed0
[<0>] md_do_sync+0x779/0x1110
[<0>] md_thread+0x90/0x160
[<0>] kthread+0xbe/0xf0
[<0>] ret_from_fork+0x34/0x50
[<0>] ret_from_fork_asm+0x1a/0x30
kworker/u1040:2+flush-253:4
[<0>] wait_barrier+0x1de/0x220
[<0>] regular_request_wait+0x30/0x180
[<0>] raid10_make_request+0x261/0x1000
[<0>] md_handle_request+0x13b/0x230
[<0>] __submit_bio+0x107/0x1f0
[<0>] submit_bio_noacct_nocheck+0x16f/0x390
[<0>] ext4_io_submit+0x24/0x40
[<0>] ext4_do_writepages+0x254/0xc80
[<0>] ext4_writepages+0x84/0x120
[<0>] do_writepages+0x7a/0x260
[<0>] __writeback_single_inode+0x3d/0x300
[<0>] writeback_sb_inodes+0x1dd/0x470
[<0>] __writeback_inodes_wb+0x4c/0xe0
[<0>] wb_writeback+0x18b/0x2d0
[<0>] wb_workfn+0x2a1/0x400
[<0>] process_one_work+0x149/0x330
[<0>] worker_thread+0x2d2/0x410
[<0>] kthread+0xbe/0xf0
[<0>] ret_from_fork+0x34/0x50
[<0>] ret_from_fork_asm+0x1a/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
net/tls: Fail tls_sw_splice_read() after a failed async decrypt
When an async decrypt fails, tls_decrypt_done() records the error in
ctx->async_wait.err and calls tls_err_abort(), which stores it in
sk_err. tls_sw_recvmsg() and tls_sw_read_sock() each read
async_wait.err once they hold the reader lock and fail the call: a
record that did not authenticate breaks the connection.
tls_sw_splice_read() has no such check, and sk_err does not stand in
for one. tls_rx_rec_wait() tests sk_err only inside the loop it
skips whenever a record is already parsed, and the first reader to
reach sock_error() clears it, while async_wait.err persists. A
splice therefore keeps delivering records on a connection that
recvmsg() and read_sock() refuse to read.
Read async_wait.err in tls_sw_splice_read() as the other two readers
do. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: digi_acceleport: fix hard lockup on disconnect
If submitting the OOB write urb fails persistently (e.g if the device is
being disconnected) the driver would loop indefinitely with interrupts
disabled.
Check for urb submission errors when sending OOB commands to avoid
hanging if, for example, open(), set_termios() or close() races with a
physical disconnect.
This is issue was flagged by Sashiko when reviewing an unrelated change
to the driver. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: composite: fix dead empty check in the USB_DT_OTG handler
The OTG branch of composite_setup() falls back to the first
configuration when none is selected:
if (cdev->config)
config = cdev->config;
else
config = list_first_entry(&cdev->configs,
struct usb_configuration, list);
if (!config)
goto done;
...
memcpy(req->buf, config->descriptors[0], value);
list_first_entry() never returns NULL. On an empty list it returns
container_of() of the list head. So the "if (!config)" check is dead.
When cdev->configs is empty, config points at the head inside struct
usb_composite_dev. config->descriptors[0] reads whatever sits at that
offset. The memcpy copies up to w_length bytes of it into the response
buffer.
cdev->configs can be empty in two cases. One is a teardown race on
gadget unbind with a control transfer in flight. The other is a driver
that sets is_otg before it adds a config. A reproducer that holds
cdev->configs empty triggers a KASAN fault in this branch.
Use list_first_entry_or_null() so the existing check does its job. |
| A lock was missing when accessing a data structure and importing certificate information into the trust database. This vulnerability affects Firefox < 80 and Firefox for Android < 80. |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: tegra: fix pm_runtime leak on mutex_lock failure
If tegra_i2c_mutex_lock() fails, the function returns without calling
pm_runtime_put(), leaking the runtime PM reference acquired by the
preceding pm_runtime_get_sync(). This prevents the device from ever
entering runtime suspend.
Add the missing pm_runtime_put() before returning on lock failure. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix af_unix iter deadlock
bpf_iter_unix_seq_show() may deadlock when lock_sock_fast() takes the fast
path and the iter prog attempts to update a sockmap. Which ends up spinning
at sock_map_update_elem()'s bh_lock_sock():
WARNING: possible recursive locking detected
test_progs/1393 is trying to acquire lock:
ffff88811ec25f58 (slock-AF_UNIX){+...}-{3:3}, at: sock_map_update_elem+0xdb/0x1f0
but task is already holding lock:
ffff88811ec25f58 (slock-AF_UNIX){+...}-{3:3}, at: __lock_sock_fast+0x37/0xe0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(slock-AF_UNIX);
lock(slock-AF_UNIX);
*** DEADLOCK ***
May be due to missing lock nesting notation
4 locks held by test_progs/1393:
#0: ffff88814b59c790 (&p->lock){+.+.}-{4:4}, at: bpf_seq_read+0x59/0x10d0
#1: ffff88811ec25fd8 (sk_lock-AF_UNIX){+.+.}-{0:0}, at: bpf_seq_read+0x42c/0x10d0
#2: ffff88811ec25f58 (slock-AF_UNIX){+...}-{3:3}, at: __lock_sock_fast+0x37/0xe0
#3: ffffffff85a6a7c0 (rcu_read_lock){....}-{1:3}, at: bpf_iter_run_prog+0x51d/0xb00
Call Trace:
dump_stack_lvl+0x5d/0x80
print_deadlock_bug.cold+0xc0/0xce
__lock_acquire+0x130f/0x2590
lock_acquire+0x14e/0x2b0
_raw_spin_lock+0x30/0x40
sock_map_update_elem+0xdb/0x1f0
bpf_prog_2d0075e5d9b721cd_dump_unix+0x55/0x4f4
bpf_iter_run_prog+0x5b9/0xb00
bpf_iter_unix_seq_show+0x1f7/0x2e0
bpf_seq_read+0x42c/0x10d0
vfs_read+0x171/0xb20
ksys_read+0xff/0x200
do_syscall_64+0x6b/0x3a0
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| A vulnerability in the ingress flow creation functionality of Cisco Adaptive Security Appliance (ASA) could allow an unauthenticated, remote attacker to cause the CPU to increase upwards of 100% utilization, causing a denial of service (DoS) condition on an affected system. The vulnerability is due to incorrect handling of an internal software lock that could prevent other system processes from getting CPU cycles, causing a high CPU condition. An attacker could exploit this vulnerability by sending a steady stream of malicious IP packets that can cause connections to be created on the targeted device. A successful exploit could allow the attacker to exhaust CPU resources, resulting in a DoS condition during which traffic through the device could be delayed. This vulnerability applies to either IPv4 or IPv6 ingress traffic. This vulnerability affects Cisco Adaptive Security Appliance (ASA) and Firepower Threat Defense (FTD) Software that is running on the following Cisco products: 3000 Series Industrial Security Appliances (ISA), ASA 5500 Series Adaptive Security Appliances, ASA 5500-X Series Next-Generation Firewalls, ASA Services Module for Cisco Catalyst 6500 Series Switches and Cisco 7600 Series Routers, Adaptive Security Virtual Appliances (ASAv), Firepower 2100 Series Security Appliances, Firepower 4110 Security Appliances, Firepower 9300 ASA Security Modules. Cisco Bug IDs: CSCvf63718. |
| A vulnerability in the FTP inspection engine of Cisco Firepower Threat Defense (FTD) Software could allow an unauthenticated, remote attacker to cause an affected device to reload, resulting in a denial of service (DoS) condition. The vulnerability exists because the affected software fails to release spinlocks when a device is running low on system memory, if the software is configured to apply FTP inspection and an access control rule to transit traffic, and the access control rule is associated with an FTP file policy. An attacker could exploit this vulnerability by sending a high rate of transit traffic through an affected device to cause a low-memory condition on the device. A successful exploit could allow the attacker to cause a software panic on the affected device, which could cause the device to reload and result in a temporary DoS condition. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: Fix pdsc_check_pci_health function to use work thread
When the driver notices fw_status == 0xff it tries to perform a PCI
reset on itself via pci_reset_function() in the context of the driver's
health thread. However, pdsc_reset_prepare calls
pdsc_stop_health_thread(), which attempts to stop/flush the health
thread. This results in a deadlock because the stop/flush will never
complete since the driver called pci_reset_function() from the health
thread context. Fix by changing the pdsc_check_pci_health_function()
to queue a newly introduced pdsc_pci_reset_thread() on the pdsc's
work queue.
Unloading the driver in the fw_down/dead state uncovered another issue,
which can be seen in the following trace:
WARNING: CPU: 51 PID: 6914 at kernel/workqueue.c:1450 __queue_work+0x358/0x440
[...]
RIP: 0010:__queue_work+0x358/0x440
[...]
Call Trace:
<TASK>
? __warn+0x85/0x140
? __queue_work+0x358/0x440
? report_bug+0xfc/0x1e0
? handle_bug+0x3f/0x70
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? __queue_work+0x358/0x440
queue_work_on+0x28/0x30
pdsc_devcmd_locked+0x96/0xe0 [pds_core]
pdsc_devcmd_reset+0x71/0xb0 [pds_core]
pdsc_teardown+0x51/0xe0 [pds_core]
pdsc_remove+0x106/0x200 [pds_core]
pci_device_remove+0x37/0xc0
device_release_driver_internal+0xae/0x140
driver_detach+0x48/0x90
bus_remove_driver+0x6d/0xf0
pci_unregister_driver+0x2e/0xa0
pdsc_cleanup_module+0x10/0x780 [pds_core]
__x64_sys_delete_module+0x142/0x2b0
? syscall_trace_enter.isra.18+0x126/0x1a0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x72/0xdc
RIP: 0033:0x7fbd9d03a14b
[...]
Fix this by preventing the devcmd reset if the FW is not running. |
| In the Linux kernel, the following vulnerability has been resolved:
af_packet: move notifier's packet_dev_mc out of rcu critical section
Syzkaller reports the following issue:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:578
__mutex_lock+0x106/0xe80 kernel/locking/mutex.c:746
team_change_rx_flags+0x38/0x220 drivers/net/team/team_core.c:1781
dev_change_rx_flags net/core/dev.c:9145 [inline]
__dev_set_promiscuity+0x3f8/0x590 net/core/dev.c:9189
netif_set_promiscuity+0x50/0xe0 net/core/dev.c:9201
dev_set_promiscuity+0x126/0x260 net/core/dev_api.c:286 packet_dev_mc net/packet/af_packet.c:3698 [inline]
packet_dev_mclist_delete net/packet/af_packet.c:3722 [inline]
packet_notifier+0x292/0xa60 net/packet/af_packet.c:4247
notifier_call_chain+0x1b3/0x3e0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2214 [inline]
call_netdevice_notifiers net/core/dev.c:2228 [inline]
unregister_netdevice_many_notify+0x15d8/0x2330 net/core/dev.c:11972
rtnl_delete_link net/core/rtnetlink.c:3522 [inline]
rtnl_dellink+0x488/0x710 net/core/rtnetlink.c:3564
rtnetlink_rcv_msg+0x7cf/0xb70 net/core/rtnetlink.c:6955
netlink_rcv_skb+0x219/0x490 net/netlink/af_netlink.c:2534
Calling `PACKET_ADD_MEMBERSHIP` on an ops-locked device can trigger
the `NETDEV_UNREGISTER` notifier, which may require disabling promiscuous
and/or allmulti mode. Both of these operations require acquiring
the netdev instance lock.
Move the call to `packet_dev_mc` outside of the RCU critical section.
The `mclist` modifications (add, del, flush, unregister) are protected by
the RTNL, not the RCU. The RCU only protects the `sklist` and its
associated `sks`. The delayed operation on the `mclist` entry remains
within the RTNL. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921: fix potential deadlock in mt7921_roc_abort_sync
roc_abort_sync() can deadlock with roc_work(). roc_work() holds
dev->mt76.mutex, while cancel_work_sync() waits for roc_work()
to finish. If the caller already owns the same mutex, both
sides block and no progress is possible.
This deadlock can occur during station removal when
mt76_sta_state() -> mt76_sta_remove() -> mt7921_mac_sta_remove() ->
mt7921_roc_abort_sync() invokes cancel_work_sync() while
roc_work() is still running and holding dev->mt76.mutex.
This avoids the mutex deadlock and preserves exactly-once
work ownership. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: fix locking in regulator_resolve_supply() error path
If late enabling of a supply regulator fails in
regulator_resolve_supply(), the code currently triggers a lockdep
warning:
WARNING: drivers/regulator/core.c:2649 at _regulator_put+0x80/0xa0, CPU#6: kworker/u32:4/596
...
Call trace:
_regulator_put+0x80/0xa0 (P)
regulator_resolve_supply+0x7cc/0xbe0
regulator_register_resolve_supply+0x28/0xb8
as the regulator_list_mutex must be held when calling _regulator_put().
To solve this, simply switch to using regulator_put().
While at it, we should also make sure that no concurrent access happens
to our rdev while we clear out the supply pointer. Add appropriate
locking to ensure that.
While the code in question will be removed altogether in a follow-up
commit, I believe it is still beneficial to have this corrected before
removal for future reference. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: sg: Resolve soft lockup issue when opening /dev/sgX
The parameter def_reserved_size defines the default buffer size reserved
for each Sg_fd and should be restricted to a range between 0 and 1,048,576
(see https://tldp.org/HOWTO/SCSI-Generic-HOWTO/proc.html). Although the
function sg_proc_write_dressz enforces this limit, it is possible to bypass
it by directly modifying the module parameter as shown below, which then
causes a soft lockup:
echo -1 > /sys/module/sg/parameters/def_reserved_size
exec 4<> /dev/sg0
watchdog: BUG: soft lockup - CPU#5 stuck for 26 seconds! [bash:537]
Modules loaded:
CPU: 5 UID: 0 PID: 537 Command: bash, kernel version 6.19.0-rc3+ #134,
PREEMPT disabled
Hardware: QEMU Standard PC (i440FX + PIIX, 1996), BIOS version
1.16.1-2.fc37 dated 04/01/2014
...
Call Trace:
sg_build_reserve+0x5c/0xa0
sg_add_sfp+0x168/0x270
sg_open+0x16e/0x340
chrdev_open+0xbe/0x230
do_dentry_open+0x175/0x480
vfs_open+0x34/0xf0
do_open+0x265/0x3d0
path_openat+0x110/0x290
do_filp_open+0xc3/0x170
do_sys_openat2+0x71/0xe0
__x64_sys_openat+0x6d/0xa0
do_syscall_64+0x62/0x310
entry_SYSCALL_64_after_hwframe+0x76/0x7e
The fix is to use module_param_cb to validate and reject invalid values
assigned to def_reserved_size. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix AMDGPU_INFO_READ_MMR_REG
There were multiple issues in that code.
First of all the order between the reset semaphore and the mm_lock was
wrong (e.g. copy_to_user) was called while holding the lock.
Then we allocated memory while holding the reset semaphore which is also
a pretty big bug and can deadlock.
Then we used down_read_trylock() instead of waiting for the reset to
finish.
(cherry picked from commit 361b6e6b303d4b691f6c5974d3eaab67ca6dd90e) |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memory-failure: fix hugetlb_lock AA deadlock in get_huge_page_for_hwpoison
Two concurrent madvise(MADV_HWPOISON) calls on the same hugetlb page can
trigger a recursive spinlock self-deadlock (AA deadlock) on hugetlb_lock
when racing with a concurrent unmap:
thread#0 thread#1
-------- --------
madvise(folio, MADV_HWPOISON)
-> poisons the folio successfully
madvise(folio, MADV_HWPOISON) unmap(folio)
try_memory_failure_hugetlb
get_huge_page_for_hwpoison
spin_lock_irq(&hugetlb_lock) <- held
__get_huge_page_for_hwpoison
hugetlb_update_hwpoison()
-> MF_HUGETLB_FOLIO_PRE_POISONED
goto out:
folio_put()
refcount: 1 -> 0
free_huge_folio()
spin_lock_irqsave(&hugetlb_lock)
-> AA DEADLOCK!
The out: path in __get_huge_page_for_hwpoison() calls folio_put() to drop
the GUP reference while the hugetlb_lock is still held by the hugetlb.c
wrapper get_huge_page_for_hwpoison(). If concurrent unmap has released
the page table mapping reference, folio_put() drops the folio refcount to
zero, triggering free_huge_folio() which attempts to re-acquire the
non-recursive hugetlb_lock.
Fix this by moving hugetlb_lock acquisition from the hugetlb.c wrapper
into get_huge_page_for_hwpoison(). Place spin_unlock_irq() before the
folio_put() at the out: label so the folio is always released outside the
lock.
[akpm@linux-foundation.org: fix race, rename label per Miaohe] |
| In the Linux kernel, the following vulnerability has been resolved:
md: fix array_state=clear sysfs deadlock
When "clear" is written to array_state, md_attr_store() breaks sysfs
active protection so the array can delete itself from its own sysfs
store method.
However, md_attr_store() currently drops the mddev reference before
calling sysfs_unbreak_active_protection(). Once do_md_stop(..., 0)
has made the mddev eligible for delayed deletion, the temporary
kobject reference taken by sysfs_break_active_protection() can become
the last kobject reference protecting the md kobject.
That allows sysfs_unbreak_active_protection() to drop the last
kobject reference from the current sysfs writer context. kobject
teardown then recurses into kernfs removal while the current sysfs
node is still being unwound, and lockdep reports recursive locking on
kn->active with kernfs_drain() in the call chain.
Reproducer on an existing level:
1. Create an md0 linear array and activate it:
mknod /dev/md0 b 9 0
echo none > /sys/block/md0/md/metadata_version
echo linear > /sys/block/md0/md/level
echo 1 > /sys/block/md0/md/raid_disks
echo "$(cat /sys/class/block/sdb/dev)" > /sys/block/md0/md/new_dev
echo "$(($(cat /sys/class/block/sdb/size) / 2))" > \
/sys/block/md0/md/dev-sdb/size
echo 0 > /sys/block/md0/md/dev-sdb/slot
echo active > /sys/block/md0/md/array_state
2. Wait briefly for the array to settle, then clear it:
sleep 2
echo clear > /sys/block/md0/md/array_state
The warning looks like:
WARNING: possible recursive locking detected
bash/588 is trying to acquire lock:
(kn->active#65) at __kernfs_remove+0x157/0x1d0
but task is already holding lock:
(kn->active#65) at sysfs_unbreak_active_protection+0x1f/0x40
...
Call Trace:
kernfs_drain
__kernfs_remove
kernfs_remove_by_name_ns
sysfs_remove_group
sysfs_remove_groups
__kobject_del
kobject_put
md_attr_store
kernfs_fop_write_iter
vfs_write
ksys_write
Restore active protection before mddev_put() so the extra sysfs
kobject reference is dropped while the mddev is still held alive. The
actual md kobject deletion is then deferred until after the sysfs
write path has fully returned. |
