| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/packet: prevent TX_RING byte count overflow
tpacket_snd() drains every SEND_REQUEST frame in a TX ring and adds
each valid packet length to the signed int len_sum. Userspace can
recycle completed frames concurrently, so a single blocking send call
is not bounded by the ring size.
After enough successful transmissions len_sum wraps into the negative
range. In particular, 65536 65535-byte frames followed by a 65007-byte
frame produce 0xfffffdef, or -EIOCBQUEUED. sock_sendmsg_nosec() treats
that as an impossible return and triggers a BUG. On systems configured
to panic on oops, a CAP_NET_RAW holder can panic the host kernel.
Stop before the next frame would make the byte count exceed INT_MAX.
The positive short count leaves that frame pending for a later send
call.
A two-thread TPACKET_V2 reproducer triggered the BUG on an arm64 build
of Linux 7.3-rc4. With this change, the same reproducer returned the
expected positive short count without an oops. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: check RCV_SHUTDOWN after the sendmsg connect wait
sctp_wait_for_connect() drops the socket lock while it sleeps. An
out-of-the-blue ABORT can then be processed from the socket backlog and
unlink the association. If a concurrent shutdown(fd, SHUT_RD) sets
RCV_SHUTDOWN, the waiter breaks with err == 0 before checking
asoc->base.dead. Its final sctp_association_put() can then free the
association, leaving sctp_sendmsg_to_asoc() to continue with a dangling
pointer.
Check RCV_SHUTDOWN along with the wait error in sctp_sendmsg_to_asoc()
before using the association again. The check only accesses the socket,
so it needs no additional association reference. Return the existing
-ESRCH so that sctp_sendmsg() skips freeing a new association that may
already have been destroyed.
Keep sctp_wait_for_connect() unchanged to preserve its behavior for the
connect() caller. |
| In the Linux kernel, the following vulnerability has been resolved:
vt: skip screen update for DEC alignment test on backgroup consoles
[BUG]
Recently, we encountered a KASAN warning as follows:
BUG: KASAN: slab-out-of-bounds in fb_pad_aligned_buffer+0x11f/0x140
Read of size 1 at addr ff1100015fd9f6a4 by task tty_fbcon_oob/1239
CPU: 7 UID: 0 PID: 1239 Comm: tty_fbcon_oob Not tainted 7.3.0-rc1 #100 PREEMPT(full)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.17.0-4.fc41 04/01/2014
Call Trace:
<TASK>
...
kasan_report+0xf0/0x120
fb_pad_aligned_buffer+0x11f/0x140
ccw_putcs+0x86c/0xa80
fbcon_putcs+0x338/0x410
do_update_region+0x21d/0x450
do_con_write+0x1e0e/0x4880
con_write+0x13/0x80
n_tty_write+0x374/0x1010
file_tty_write.isra.0+0x404/0x7a0
...
reproduce:
1) open /dev/tty0, set a KDFONTOP ioctl with op.op = KD_FONT_OP_SET,
op.width = 8 and op.height = 16 (visible VC1)
2) open /dev/tty1, set a KDFONTOP ioctl with op.op = KD_FONT_OP_SET,
op.width = 28 and op.height = 24 (invisible VC2)
3) echo 3 > /sys/devices/virtual/graphics/fbcon/rotate_all
4) write EShash8(esc hash8) to tty1
[CAUSE]
All VCs render to the framebuffer. setfont only modifies the target VC's
font without resizing the framebuffer backing buffer (par->rotated.buf);
the buffer is only resized for the visible VC
(fbcon_do_set_font -> ... -> vc_do_resize -> update_screen). This relies on
the con_should_update() check performed before every update_region().
However, the ESC # 8 path (do_con_trol -> do_update_region) omits the
con_should_update() check. After changing the font size of an invisible VC,
do_update_region() fills using the new font size against a buffer that was
never resized, causing an out-of-bounds access.
[FIX]
Only push the update when the console is visible and not blanked, add
the con_should_update() check in the do_con_trol() like every other call
site of do_update_region() (update_region(), invert_screen(), ...). |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: core: call _get_device() with the master MTD
__get_mtd_device() calls the master's _get_device() callback with mtd,
which may be a partition. __put_mtd_device() passes the master.
This breaks gluebi partitions because gluebi_get_device() uses
container_of() and therefore requires the master MTD. Pass the master
to _get_device(), matching _put_device(). |
| In the Linux kernel, the following vulnerability has been resolved:
of/overlay: don't leak fragment references when changeset init fails
init_overlay_changeset() stores the number of initialized fragments
in ovcs->count only on full success. When find_target() or the
__symbols__ lookup fails partway through, the target and overlay
references taken for the fragments initialized so far are never
dropped: free_overlay_changeset() bounds its cleanup loop by
ovcs->count, which is still 0.
Store the running count on the error path so free_overlay_changeset()
puts whatever was set up. The store is guarded by ovcs->fragments
because on the allocation-failure path cnt still holds the counting
pass total while there is no fragments array; everywhere else cnt
only counts fully-initialized fragments. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: preserve hidden-group beacon IE ownership
A hidden-group probe-response entry borrows its beacon IEs from the
group's beacon entry. cfg80211_update_assoc_bss_entry() can pass such
an entry to cfg80211_update_known_bss() when merging scan entries
after a channel switch.
Copying the borrowed beacon_ies into the associated entry gives the
same allocation two owners. Releasing the group's beacon entry can
then leave the associated entry pointing to freed IEs, which are
freed again when that entry is released.
Skip beacon IE replacement when the source entry belongs to a hidden
group. Preserve probe-response processing, the subsequent metadata
updates, and the existing rejection path for conflicting hidden
beacon updates. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btintel: validate DDC record lengths
Parse DDC record lengths in unsigned storage so 0xFF does not wrap.
Reject records smaller than the mandatory three-byte header, records
exceeding U8_MAX, and records exceeding remaining firmware bytes before
issuing Intel_Write_DDC.
This issue was reported by Claude Mythos. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: cls_api: reclaim an empty proto on the error path
Two racing tc filter add requests on the same chain/prio of an
unlocked classifier both run change() on the shared proto and both
can fail: the winner's tcf_chain_tp_delete_empty() attempt gives up
because the loser's handle is still in the idr, and the loser's
error path drops only its own reference without a second reclamation
attempt. The empty proto stays linked in the chain, holding the
chain reference, a block reference and the classifier module
reference until the chain or block is torn down.
Reclaim the proto on the error path of any failed request that holds
a proto reference. The reclamation is emptiness-gated:
tcf_chain_tp_delete_empty() unlinks the proto only when
delete_empty() admits it is empty, so a live shared proto is never
unlinked. A proto the request created is reclaimed unconditionally -
it is the only owner, so marking it for deletion is safe even without
a delete_empty callback. Classifiers without one (the check marks the
proto unconditionally) are rtnl-serialized, so the raced window this
guard closes cannot arise for them.
This is a follow-up to commit d4e359b3608a ("net/sched: cls_api: fix
teardown of an adopted proto on insert-race loss"), which stopped the
loser of the insert race from unlinking the winner's live proto but
left the empty-proto residual in place.
Conditions to recreate:
- CONFIG_NET_CLS_FLOWER=y; veth pair
- tc qdisc add dev veth0 ingress
- two concurrent `tc filter add dev veth0 ingress protocol ip pref 1
flower skip_sw ... action drop` (both fail in fl_hw_replace_filter
after publishing their handle in the idr); repeat in a loop
- an empty flower tp stays linked after both requests fail; visible
as a bare `filter protocol ip pref 1 flower chain 0` header in
`tc filter show` with no filter entries
- CAP_NET_ADMIN (namespace-local via unshare -Urn suffices) |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: don't drain cmd_sync backlog on unregister
hci_unregister_dev() disables cmd_work and cmd_timer, then calls
hci_cmd_sync_clear(), whose cancel_work_sync() waits for
hci_cmd_sync_work() to return. That worker dequeues and runs every
entry on cmd_sync_work_list. With cmd_work disabled nothing reaches
the controller, so each queued HCI command waits the full
HCI_CMD_TIMEOUT (2s).
The backlog has no bound. Userspace can keep queuing MGMT commands
such as MGMT_OP_GET_CLOCK_INFO against a controller that doesn't
answer. Closing /dev/vhci then blocks in vhci_release() for
backlog * 2s:
INFO: task syz-executor:5749 blocked for more than 143 seconds.
cancel_work_sync
hci_cmd_sync_clear
hci_unregister_dev
vhci_release
In a local reproduction the backlog held more than 5000 entries,
which comes to hours of hang.
Stop the worker from taking new entries once HCI_UNREGISTER is set,
and wake any request still waiting with -ENODEV before cancelling
the work. The entries left over are destroyed with -ECANCELED by the
existing sweep in hci_cmd_sync_clear(). They stay on the list until
the work has stopped, so hci_cmd_sync_dequeue() and friends still see
them. A callback already running may still issue another command,
which delays unregister by at most one timeout per remaining command,
not by the whole backlog. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: prevent GCM nonce reuse on peer key changes
TIPC can encrypt traffic between nodes using a different transmit key
for each node. In this mode, the AES-GCM nonce for a packet sent to a
known peer consists of a 32-bit prefix (a per-key salt XOR the peer's
address) followed by a 64-bit counter. That counter is stored in the
peer's RX crypto object. When the peer reports a change in which key
it uses to receive packets, TIPC resets this counter. The sender can
still be using the same TX key and salt, so subsequent packets reuse
earlier nonces. This nonce reuse breaks confidentiality and exposes
GCM's authentication key. This makes forgeries trivial: an attacker
can exploit CTR malleability to alter captured ciphertexts and use the
recovered authentication key to compute a valid tag for the modified
ciphertext, under the same key and nonce.
Use the TX key's existing aead->seqno counter instead. All encryptions
using that key object share the same atomic counter, so concurrent
encryptions get distinct nonce counter values. The counter survives
key activation and peer reconnection, and peer key-status reports
cannot reset it. This prevents those transitions from causing nonce
reuse while the same TX key remains installed.
The nonce format is unchanged, and receivers do not require consecutive
counter values, so sharing the counter across peers remains compatible
with existing receivers. A pre-existing check still invokes key
revocation in the unlikely event that the counter wraps to zero. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bcmgenet: fix NULL dereference in set_coalesce before first open
The Rx ring priv and index are only set in bcmgenet_init_rx_ring(),
which runs at open. Setting the Rx coalescing parameters on an interface
that was never opened, e.g. "ethtool -C eth0 rx-usecs 50", dereferences
a NULL ring->priv. The oops happens with RTNL held, so networking
stays stuck until a reboot:
Unable to handle kernel paging request at virtual address 0000000000002788
pc : bcmgenet_set_rx_coalesce.isra.0+0x10/0x88
lr : bcmgenet_set_coalesce+0xe8/0x180
Call trace:
bcmgenet_set_rx_coalesce.isra.0+0x10/0x88 (P)
__ethnl_set_coalesce.isra.0+0x490/0x570
ethnl_set_coalesce+0x48/0xc0
ethnl_default_set_doit+0xf4/0x230
genl_family_rcv_msg_doit+0xe8/0x160
genl_rcv_msg+0x220/0x2a0
netlink_rcv_skb+0x68/0x140
genl_rcv+0x40/0x60
netlink_unicast+0x338/0x3c0
netlink_sendmsg+0x19c/0x3f8
__sock_sendmsg+0x64/0xc0
__sys_sendto+0x124/0x198
__arm64_sys_sendto+0x30/0x48
Set priv and index at probe. Writing the registers while the interface
is down is harmless because open resets the MAC and
bcmgenet_init_rx_coalesce() reapplies the stored values.
It was observed on a Raspberry Pi CM4, but should apply to all other
genet devices. |
| In the Linux kernel, the following vulnerability has been resolved:
ipvs: filter some flags received in the backup server
While the IPVS SYNC protocol is not secure by design
we can still protect the backup server from messages that
can wreak havoc.
This commit addresses problems from received connection flags
or their combinations. We now drop messages as follows:
1. the NO_CPORT+TEMPLATE combination allows lookups for normal
connections to hit template which can break in many ways.
While the master does not sync connections with NO_CPORT flag,
i.e. before they are established, we still accept NO_CPORT
without TEMPLATE.
2. ONE_PACKET: it is not sent by master, so we do not
expect it in backup. Before now it was ignored by
IP_VS_CONN_F_BACKUP_MASK for protocol v1 while protocol
v0 created connections that are not hashed and dropped
immediately. Better to apply the IP_VS_CONN_F_BACKUP_MASK
also to the flags from v0 messages for consistency with v1. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: bpf: reject invalid NAT manipulation types
As bpf_ct_set_nat_info() is not validating the NAT manipulation type a
wrong value can be passed directly to nf_nat_setup_info(). This triggers
the WARN_ON() at nf_nat_setup_info() and if panic_on_warn isn't set,
then IPS_SRC_NAT_DONE is set without adding nat_bysource and conntrack
cleanup tries to unlink an uninitialized hlist node.
Fix this by checking that NAT manipulation type is correct before
calling nf_nat_setup_info(). In addition, if the WARN_ON is hit, return
NF_DROP instead of continuing with the processing to avoid similar
situations in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix race between perf_event_exit_task() and perf_pending_task()
A race condition exists between perf_event_exit_task() and
perf_pending_task() during begin_new_exec().
During begin_new_exec(), perf_event_exit_task() may be called, and the
PF_EXITING flag is not set on task. So perf_sigtrap() continues to execute
and triggers WARN_ON_ONCE(event->ctx->task != current).
Since both task exit and exec paths can call perf_event_exit_task() which
sets ctx->task to TASK_TOMBSTONE, fix this by explicitly checking if
event->ctx->task equals TASK_TOMBSTONE and dropping the redundant
PF_EXITING check. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/gfx6: fix firmware leak on teardown
The firmware requested in gfx_v6_0_init_microcode() is not released
when the GFX block is torn down, leaking the firmware resources.
Add gfx_v6_0_free_microcode() and call it from gfx_v6_0_sw_fini()
to release the PFP, ME, CE and RLC firmware.
(cherry picked from commit 386e81346f95ab0be5a82c5535de932e7a456924) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix ACP MFD device leak on init failure
acp_hw_init() registers ACP child devices with mfd_add_devices() before
attaching them to the ACP power domain and initializing the hardware.
If attaching a child to the power domain fails, or if the ACP reset or
clock enable operation times out, the failure path frees only the
source cell, resource, and platform-data allocations. The child
platform devices already registered by mfd_add_devices() remain
registered and are never released.
Remove the children from the power domain and unregister the MFD
devices on failures that occur after mfd_add_devices() succeeds. Keep
mfd_add_devices() failures on the existing cleanup path since the MFD
core already rolls back partially registered children itself.
The issue was identified by a static analysis tool I developed and
confirmed by manual review.
(cherry picked from commit 63da68d6a2279ec945581c990c5a59a5ae8b5560) |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: fix port tear down use-after-free
Some drivers for multiport devices access port driver data from
completion handlers of shared URBs submitted at attach() or first open()
and stopped at disconnect() or last close(), respectively.
A simple NULL check before accessing the driver data makes sure that a
port state container has at least been allocated, but a completion
handler can still race with port tear down.
Reorder the disconnect handling so that ports are not deregistered (and
their driver data freed) until after all ports have been hung up and the
driver disconnect() callback has run so that all I/O has been stopped. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: core: clear both ep_in and ep_out for non-ep0 control endpoints
In usb_enable_endpoint(), non-zero control endpoints (where
usb_endpoint_xfer_control(&ep->desc) is true) populate both
dev->ep_in[epnum] and dev->ep_out[epnum] with the same struct
usb_host_endpoint pointer.
However, usb_disable_endpoint() only clears either dev->ep_out[epnum] or
dev->ep_in[epnum] depending on the direction bit of epaddr when
reset_hardware is set, leaving the opposite direction's array slot
pointing to the disabled/freed endpoint.
Clear both dev->ep_out[epnum] and dev->ep_in[epnum] when disabling a
non-ep0 control endpoint with reset_hardware set, and update the
function kerneldoc accordingly.
Tested in QEMU against Linux 7.3.0-rc3 using dummy_hcd and raw-gadget to
enumerate a USB device with a non-zero control endpoint
(bEndpointAddress 0x01, bmAttributes USB_ENDPOINT_XFER_CONTROL),
verifying that both dev->ep_in[1] and dev->ep_out[1] are cleared when
the interface is disabled. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: dwc2: shut down wakeup timer before freeing HCD state
dwc2_wakeup_detected() accesses the DWC2 host state and can rearm the
wakeup timer. dwc2_hcd_free() currently deletes the timer only after
freeing host-owned state, and timer_delete() does not synchronize a
callback or prevent it from being queued again.
Stop and shut down the timer in dwc2_hcd_release(), before the HCD
resources are freed. This covers both the HCD initialization error path
and normal HCD removal. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_core: Serialize ACL scheduling with channel deletion
hci_chan_sent() selects a channel under RCU but drops the read lock before
accessing chan->conn and returning the channel. The ACL and LE schedulers
then use its packet queue and update its transmit counters without any
protection against channel deletion.
After TX selects a channel and releases RCU, a disconnect command timeout
on the separate request workqueue can run hci_conn_failed() and
l2cap_conn_del(). hci_chan_del() can then unlink the channel, complete
synchronize_rcu(), purge its queue and free it before TX resumes. This
causes use-after-free both in hci_chan_sent() and in its callers.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_chan_sent+0x892/0x9b0
Workqueue: hci0 hci_tx_work
Call Trace:
hci_chan_sent+0x892/0x9b0
hci_tx_work+0x5e6/0xb70
Allocated by task 91:
hci_chan_create+0xe3/0x350
l2cap_conn_add.part.0+0x12/0xa30
l2cap_chan_connect+0x110d/0x1b60
l2cap_sock_connect+0x310/0x530
Freed by task 99:
hci_chan_del+0x11f/0x170
l2cap_conn_del+0x4f1/0x800
l2cap_connect_cfm+0x88c/0xd30
hci_conn_failed+0x150/0x250
hci_abort_conn_sync+0x3e3/0x800
hci_cmd_sync_run+0x7e/0xc0
hci_abort_conn+0x105/0x1f0
disconnect_sync+0x157/0x290
hci_cmd_sync_work+0x13c/0x290
Hold the existing device mutex across channel selection and transmission
in both schedulers to serialize them with channel teardown. Keep timeout
handling outside the critical sections because hci_link_tx_to() acquires
the same mutex. This also permits the transmit path to sleep, unlike
extending the RCU read-side critical section across packet submission. |
