| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: digi_acceleport: fix memory corruption with small endpoints
Add the missing bulk-out buffer size sanity checks to avoid
out-of-bounds memory accesses or slab corruption should a malicious
device report smaller buffers than expected. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: cypress_m8: validate interrupt packet headers
cypress_read_int_callback() parses the interrupt-in buffer according to
the selected Cypress packet format. Format 1 has a two-byte status/count
header and format 2 has a one-byte combined status/count header. The
usb-serial core sizes the interrupt-in buffer from the endpoint
descriptor's wMaxPacketSize, and successful interrupt transfers can
complete short when URB_SHORT_NOT_OK is not set.
Check that the completed packet contains the selected header before
reading it. Malformed short reports are ignored and the interrupt URB is
resubmitted through the existing retry path, preventing out-of-bounds
header-byte reads.
KASAN report as below:
KASAN slab-out-of-bounds in cypress_read_int_callback+0x240/0x7f0
Read of size 1
Call trace:
cypress_read_int_callback() (drivers/usb/serial/cypress_m8.c:1009)
__usb_hcd_giveback_urb()
dummy_timer()
[ johan: use constants in header length sanity checks ] |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: belkin_sa: validate interrupt status length
The Belkin interrupt callback treats interrupt data as a four-byte
status report and reads LSR/MSR fields at offsets 2 and 3. The
interrupt-in buffer length is derived from endpoint wMaxPacketSize, and
short interrupt transfers may complete successfully with a smaller
actual_length.
Check the completed interrupt packet length before parsing status
fields so short interrupt endpoints and short successful packets are
ignored instead of causing out-of-bounds or stale status-byte reads.
KASAN report as below:
BUG: KASAN: slab-out-of-bounds in belkin_sa_read_int_callback()
Read of size 1
Call trace:
belkin_sa_read_int_callback() (drivers/usb/serial/belkin_sa.c:202)
__usb_hcd_giveback_urb() (drivers/usb/core/hcd.c:1630)
dummy_timer() (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
usb: usbtmc: check URB actual_length for interrupt-IN notifications
USBTMC devices can use an optional interrupt endpoint for notification
messages. These typically contain two-byte headers indicating the
payload format, but the driver does not check if these headers are
present before accessing the data buffers. In cases where the URB
actual_length is not enough to fit these headers, the driver will either
cause an out-of-bounds read, or consume stale leftover data from a
previous notification.
Fix by checking if actual_data contains enough bytes for the headers,
otherwise resubmit URB to the interrupt endpoint. |
| In the Linux kernel, the following vulnerability has been resolved:
usbip: vudc: Fix use after free bug in vudc_remove due to race condition
This patch follows up Zheng Wang's 2023 report of a use-after-free in
vudc_remove(). The original thread stalled on Shuah Khan's request for
runtime testing of the unplug/unbind path. This patch supplies that
testing and keeps Zheng's original fix shape.
In vudc_probe(), v_init_timer() binds udc->tr_timer.timer to v_timer().
usbip_sockfd_store() starts the timer via v_start_timer()/v_kick_timer().
vudc_remove() can then free the containing struct vudc while the timer is
still pending or executing.
KASAN confirms the race on an unpatched x86_64 QEMU guest with
CONFIG_KASAN=y, CONFIG_USBIP_VUDC=y, CONFIG_USB_ZERO=y, and a tight loop
that repeatedly writes a socket fd to usbip_sockfd, closes the socket
pair, and unbinds/rebinds usbip-vudc.0:
BUG: KASAN: slab-use-after-free in __run_timer_base.part.0+0x8ba/0x8e0
Write of size 8 at addr ffff888001b80740 by task trigger_and_unb/239
Allocated by task 239:
vudc_probe+0x4d/0xaa0
Freed by task 239:
kfree+0x18f/0x520
device_release_driver_internal+0x388/0x540
unbind_store+0xd9/0x100
This lands in the timer core rather than v_timer() itself because the
embedded timer_list is being walked after its containing struct vudc has
already been freed. The underlying lifetime bug is the same one Zheng
reported.
With v_stop_timer() called from vudc_remove() and the timer deleted
synchronously, the same harness completed 5000 bind/unbind iterations
with no KASAN report. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: tcpm/tcpci_maxim: validate header NDO against RX_BYTE_CNT
A broken/malicious port can transmit a CRC-valid frame whose header
advertises up to seven data objects but whose body carries fewer than
that. Check for this, and rightfully reject the message, instead of
reading from uninitialized stack memory. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: safe_serial: fix memory corruption with small endpoint
Make sure that the bulk-out buffer size is at least eight bytes to avoid
user-controlled slab corruption in "safe" mode should a malicious device
report a smaller size. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: cypress_m8: fix memory corruption with small endpoint
Make sure that the interrupt-out endpoint max packet size is at least
eight bytes to avoid user-controlled slab corruption or NULL-pointer
dereference should a malicious device report a smaller size. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: ucsi: validate connector number in ucsi_connector_change()
The connector number in a UCSI CCI notification is a 7-bit field
supplied by the PPM. ucsi_connector_change() uses it to index the
ucsi->connector[] array without checking it against the number of
connectors the PPM reported at init time, so a buggy or malicious PPM
(EC firmware, or an I2C-attached UCSI controller on the ccg / stm32g0 /
glink transports) can drive schedule_work() on memory past the end of
the array.
Reject connector numbers that are zero or exceed cap.num_connectors
before dereferencing the array. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: wcove: don't write past struct pd_message in wcove_read_rx_buffer()
wcove_read_rx_buffer() copies the PD RX FIFO into the caller's
struct pd_message with
for (i = 0; i < USBC_RXINFO_RXBYTES(info); i++)
regmap_read(wcove->regmap, USBC_RX_DATA + i, msg + i);
which has two problems:
USBC_RXINFO_RXBYTES() is a 5-bit field (max 31) while struct pd_message
is 30 bytes (__le16 header + __le32 payload[PD_MAX_PAYLOAD], packed).
The byte count latched in RXINFO is the number of bytes the port partner
put on the wire, so a malicious partner that transmits a 31-byte frame
can drive the loop one byte past the destination if the WCOVE BMC
receiver does not enforce the PD object-count limit in hardware. The
existing FIXME flagged this as unverified.
Independently, regmap_read() takes an unsigned int * and stores a full
unsigned int at the destination. Passing the byte pointer msg + i means
each iteration writes four bytes; the high three are zero (val_bits is
8) and are normally overwritten by the next iteration, but the final
iteration's high bytes are not. With RXBYTES == 30 the i == 29 iteration
already writes three zero bytes past msg, which sits on the IRQ thread's
stack in wcove_typec_irq().
Clamp the loop to sizeof(struct pd_message) and read each register into
a local before storing only its low byte, so the copy can never exceed
the destination regardless of what RXINFO reports. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: typec: altmodes/displayport: validate count before reading Status Update VDO
A broken/malicious device can send the incorrect count for a status
update VDO, which will cause the kernel to read uninitialized stack data
and send it off elsewhere.
Fix this up by correctly verifying the count for the update object. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: atmel_mxt_ts - fix boundary check in mxt_prepare_cfg_mem
When a configuration file provides an object size that is larger than the
driver's known mxt_obj_size(object), the driver intends to discard the
extra bytes.
The loop iterates using for (i = 0; i < size; i++). Inside the loop, the
condition to skip processing extra bytes is:
if (i > mxt_obj_size(object))
continue;
Since i is a 0-based index, the valid indices for the object are 0 through
mxt_obj_size(object) - 1.
When i == mxt_obj_size(object), the condition evaluates to false, and the
code processes the byte instead of discarding it.
This causes the code to calculate byte_offset = reg + i - cfg->start_ofs
and writes the byte there, overwriting exactly one byte of the adjacent
instance or object.
Update the boundary check to skip extra bytes correctly by using >=. |
| In the Linux kernel, the following vulnerability has been resolved:
USB: serial: omninet: fix memory corruption with small endpoint
Make sure that the bulk-out buffers are at least as large as the
hardcoded transfer size to avoid user-controlled slab corruption should
a malicious device report a smaller endpoint max packet size than
expected. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: scd30: fix division by zero in write_raw
Add a zero check for val2 before using it as a divisor when setting the
sampling frequency. A user writing a zero fractional part to the
sampling_frequency sysfs attribute triggers a division by zero in the
kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: adis16260: fix division by zero in write_raw
Add a validation check for the sampling frequency value before using it
as a divisor. A user writing zero to the sampling_frequency sysfs
attribute triggers a division by zero in the kernel. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: gyro: itg3200: fix i2c read into the wrong stack location
itg3200_read_all_channels() takes `__be16 *buf' as a parameter and
fills the i2c_msg destination as `(char *)&buf'. Since `buf' is the
parameter (a pointer), `&buf' is the address of the local pointer
slot on the stack of itg3200_read_all_channels(), not the address
of the caller's scan buffer. The (char *) cast hides the type
mismatch.
i2c_transfer() therefore writes ITG3200_SCAN_ELEMENTS * sizeof(s16)
= 8 bytes into the parameter's stack slot, which is discarded when
the function returns. The caller's scan buffer in
itg3200_trigger_handler() is never written to, so
iio_push_to_buffers_with_timestamp() pushes uninitialised stack
contents to userspace via /dev/iio:deviceX every scan -- both a
functional bug (no actual gyroscope or temperature data is
delivered through the triggered buffer) and an information leak.
The non-buffered read_raw() path is unaffected: it goes through
itg3200_read_reg_s16() which uses `&out' on a local s16 value,
where that is correct.
Drop the spurious `&' so the i2c read writes into the caller's
buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
Input: xpad - fix out-of-bounds access for Share button
xpadone_process_packet() receives len directly from urb->actual_length
and uses it to index the share-button byte at data[len - 18] or
data[len - 26]. Since both len and data[0] are under the device's
control, a broken controller can send a GIP_CMD_INPUT packet with
actual_length < 18 (e.g. 5 bytes) and reach this code path, causing
accesses beyond the actual array.
Fix this by calculating the offset and checking bounds against the
packet length. |
| In the Linux kernel, the following vulnerability has been resolved:
auxdisplay: line-display: fix OOB read on zero-length message_store()
linedisp_display() unconditionally reads msg[count - 1] before
checking whether count is zero, so a write of zero bytes to the
message sysfs attribute hits msg[-1]:
write(fd, "", 0);
-> message_store(..., buf, count=0)
-> linedisp_display(linedisp, buf, count=0)
-> msg[count - 1] == '\n' ; OOB read
The kernfs write buffer for that store is a 1-byte allocation
(kernfs_fop_write_iter() does kmalloc(len + 1) with len == 0),
so msg[-1] is a 1-byte read before the slab object. On a
KASAN-enabled kernel this trips an out-of-bounds report and
panics; on stock kernels it silently reads adjacent slab data
and, if that byte happens to be '\n', the following count--
wraps ssize_t 0 to -1 and is then passed to kmemdup_nul().
linedisp_display() is reached from the message_store() sysfs
callback (drivers/auxdisplay/line-display.c message attribute,
mode 0644) and from the in-tree initial-message setup with
count == -1, so the OOB path is only userspace-triggerable via
zero-byte writes; vfs_write() does not short-circuit on
count == 0 and kernfs_fop_write_iter() dispatches the store
callback regardless.
Guard the trailing-newline trim with a count check. The
existing if (!count) block then takes the clear-display path
unchanged.
Affects every auxdisplay driver that registers via
linedisp_register() / linedisp_attach(): ht16k33, max6959,
img-ascii-lcd, seg-led-gpio. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
