| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: fix OOB access in DBG_BUF_PRODUCER async event handler
The ASYNC_EVENT_CMPL_EVENT_ID_DBG_BUF_PRODUCER handler in
bnxt_async_event_process() uses a firmware-supplied 'type' field
directly as an index into bp->bs_trace[] without bounds validation.
The 'type' field is a 16-bit value extracted from DMA-mapped completion
ring memory that the NIC writes directly to host RAM. A malicious or
compromised NIC can supply any value from 0 to 65535, causing an
out-of-bounds access into kernel heap memory.
The bnxt_bs_trace_check_wrap() call then dereferences bs_trace->magic_byte
and writes to bs_trace->last_offset and bs_trace->wrapped, leading to
kernel memory corruption or a crash.
Fix by adding a bounds check and defining BNXT_TRACE_MAX as
DBG_LOG_BUFFER_FLUSH_REQ_TYPE_ERR_QPC_TRACE + 1 to cover all currently
defined firmware trace types (0x0 through 0xc). |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: cdc_ncm: add ndpoffset to NDP16 nframes bounds check
cdc_ncm_rx_verify_ndp16() validates that the NDP header and its DPE
entries fit within the skb. The first check correctly accounts for
ndpoffset:
if ((ndpoffset + sizeof(struct usb_cdc_ncm_ndp16)) > skb_in->len)
but the second check omits it:
if ((sizeof(struct usb_cdc_ncm_ndp16) +
ret * (sizeof(struct usb_cdc_ncm_dpe16))) > skb_in->len)
This validates the DPE array size against the total skb length as if
the NDP were at offset 0, rather than at ndpoffset. When the NDP is
placed near the end of the NTB (large wNdpIndex), the DPE entries can
extend past the skb data buffer even though the check passes.
cdc_ncm_rx_fixup() then reads out-of-bounds memory when iterating
the DPE array.
Add ndpoffset to the nframes bounds check and use struct_size_t() to
express the NDP-plus-DPE-array size more clearly. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: cdc_ncm: add ndpoffset to NDP32 nframes bounds check
The same bounds-check bug fixed for NDP16 in the previous patch also
exists in cdc_ncm_rx_verify_ndp32(). The DPE array size is validated
against the total skb length without accounting for ndpoffset, allowing
out-of-bounds reads when the NDP32 is placed near the end of the NTB.
Add ndpoffset to the nframes bounds check and use struct_size_t() to
express the NDP-plus-DPE-array size more clearly.
Compile-tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
nfnetlink_osf: validate individual option lengths in fingerprints
nfnl_osf_add_callback() validates opt_num bounds and string
NUL-termination but does not check individual option length fields.
A zero-length option causes nf_osf_match_one() to enter the option
matching loop even when foptsize sums to zero, which matches packets
with no TCP options where ctx->optp is NULL:
Oops: general protection fault
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
RIP: 0010:nf_osf_match_one (net/netfilter/nfnetlink_osf.c:98)
Call Trace:
nf_osf_match (net/netfilter/nfnetlink_osf.c:227)
xt_osf_match_packet (net/netfilter/xt_osf.c:32)
ipt_do_table (net/ipv4/netfilter/ip_tables.c:293)
nf_hook_slow (net/netfilter/core.c:623)
ip_local_deliver (net/ipv4/ip_input.c:262)
ip_rcv (net/ipv4/ip_input.c:573)
Additionally, an MSS option (kind=2) with length < 4 causes
out-of-bounds reads when nf_osf_match_one() unconditionally accesses
optp[2] and optp[3] for MSS value extraction. While RFC 9293
section 3.2 specifies that the MSS option is always exactly 4
bytes (Kind=2, Length=4), the check uses "< 4" rather than
"!= 4" because lengths greater than 4 do not cause memory
safety issues -- the buffer is guaranteed to be at least
foptsize bytes by the ctx->optsize == foptsize check.
Reject fingerprints where any option has zero length, or where an MSS
option has length less than 4, at add time rather than trusting these
values in the packet matching hot path. |
| In the Linux kernel, the following vulnerability has been resolved:
Squashfs: check metadata block offset is within range
Syzkaller reports a "general protection fault in squashfs_copy_data"
This is ultimately caused by a corrupted index look-up table, which
produces a negative metadata block offset.
This is subsequently passed to squashfs_copy_data (via
squashfs_read_metadata) where the negative offset causes an out of bounds
access.
The fix is to check that the offset is within range in
squashfs_read_metadata. This will trap this and other cases. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix incorrect buffer cleanup in gve_tx_clean_pending_packets for QPL
In DQ-QPL mode, gve_tx_clean_pending_packets() incorrectly uses the RDA
buffer cleanup path. It iterates num_bufs times and attempts to unmap
entries in the dma array.
This leads to two issues:
1. The dma array shares storage with tx_qpl_buf_ids (union).
Interpreting buffer IDs as DMA addresses results in attempting to
unmap incorrect memory locations.
2. num_bufs in QPL mode (counting 2K chunks) can significantly exceed
the size of the dma array, causing out-of-bounds access warnings
(trace below is how we noticed this issue).
UBSAN: array-index-out-of-bounds in
drivers/net/ethernet/drivers/net/ethernet/google/gve/gve_tx_dqo.c:178:5 index 18 is out of
range for type 'dma_addr_t[18]' (aka 'unsigned long long[18]')
Workqueue: gve gve_service_task [gve]
Call Trace:
<TASK>
dump_stack_lvl+0x33/0xa0
__ubsan_handle_out_of_bounds+0xdc/0x110
gve_tx_stop_ring_dqo+0x182/0x200 [gve]
gve_close+0x1be/0x450 [gve]
gve_reset+0x99/0x120 [gve]
gve_service_task+0x61/0x100 [gve]
process_scheduled_works+0x1e9/0x380
Fix this by properly checking for QPL mode and delegating to
gve_free_tx_qpl_bufs() to reclaim the buffers. |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kalmia: validate USB endpoints
The kalmia driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: Fix possible oob access in mt7925_mac_write_txwi_80211()
Check frame length before accessing the mgmt fields in
mt7925_mac_write_txwi_80211 in order to avoid a possible oob access. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/userq: Do not allow userspace to trivially triger kernel warnings
Userspace can either deliberately pass in the too small num_fences, or the
required number can legitimately grow between the two calls to the userq
wait ioctl. In both cases we do not want the emit the kernel warning
backtrace since nothing is wrong with the kernel and userspace will simply
get an errno reported back. So lets simply drop the WARN_ONs.
(cherry picked from commit 2c333ea579de6cc20ea7bc50e9595ef72863e65c) |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/mbox: validate payload size before accessing contents in cxl_payload_from_user_allowed()
cxl_payload_from_user_allowed() casts and dereferences the input
payload without first verifying its size. When a raw mailbox command
is sent with an undersized payload (ie: 1 byte for CXL_MBOX_OP_CLEAR_LOG,
which expects a 16-byte UUID), uuid_equal() reads past the allocated buffer,
triggering a KASAN splat:
BUG: KASAN: slab-out-of-bounds in memcmp+0x176/0x1d0 lib/string.c:683
Read of size 8 at addr ffff88810130f5c0 by task syz.1.62/2258
CPU: 2 UID: 0 PID: 2258 Comm: syz.1.62 Not tainted 6.19.0-dirty #3 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xab/0xe0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xce/0x650 mm/kasan/report.c:482
kasan_report+0xce/0x100 mm/kasan/report.c:595
memcmp+0x176/0x1d0 lib/string.c:683
uuid_equal include/linux/uuid.h:73 [inline]
cxl_payload_from_user_allowed drivers/cxl/core/mbox.c:345 [inline]
cxl_mbox_cmd_ctor drivers/cxl/core/mbox.c:368 [inline]
cxl_validate_cmd_from_user drivers/cxl/core/mbox.c:522 [inline]
cxl_send_cmd+0x9c0/0xb50 drivers/cxl/core/mbox.c:643
__cxl_memdev_ioctl drivers/cxl/core/memdev.c:698 [inline]
cxl_memdev_ioctl+0x14f/0x190 drivers/cxl/core/memdev.c:713
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x18e/0x210 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xa8/0x330 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fdaf331ba79
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fdaf1d77038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fdaf3585fa0 RCX: 00007fdaf331ba79
RDX: 00002000000001c0 RSI: 00000000c030ce02 RDI: 0000000000000003
RBP: 00007fdaf33749df R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fdaf3586038 R14: 00007fdaf3585fa0 R15: 00007ffced2af768
</TASK>
Add 'in_size' parameter to cxl_payload_from_user_allowed() and validate
the payload is large enough. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: Use correct version for UAC3 header validation
The entry of the validators table for UAC3 AC header descriptor is
defined with the wrong protocol version UAC_VERSION_2, while it should
have been UAC_VERSION_3. This results in the validator never matching
for actual UAC3 devices (protocol == UAC_VERSION_3), causing their
header descriptors to bypass validation entirely. A malicious USB
device presenting a truncated UAC3 header could exploit this to cause
out-of-bounds reads when the driver later accesses unvalidated
descriptor fields.
The bug was introduced in the same commit as the recently fixed UAC3
feature unit sub-type typo, and appears to be from the same copy-paste
error when the UAC3 section was created from the UAC2 section. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: Fix possible oob access in mt76_connac2_mac_write_txwi_80211()
Check frame length before accessing the mgmt fields in
mt76_connac2_mac_write_txwi_80211 in order to avoid a possible oob
access.
[fix check to also cover mgmt->u.action.u.addba_req.capab,
correct Fixes tag] |
| In the Linux kernel, the following vulnerability has been resolved:
net: usb: kaweth: validate USB endpoints
The kaweth driver should validate that the device it is probing has the
proper number and types of USB endpoints it is expecting before it binds
to it. If a malicious device were to not have the same urbs the driver
will crash later on when it blindly accesses these endpoints. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf/bonding: reject vlan+srcmac xmit_hash_policy change when XDP is loaded
bond_option_mode_set() already rejects mode changes that would make a
loaded XDP program incompatible via bond_xdp_check(). However,
bond_option_xmit_hash_policy_set() has no such guard.
For 802.3ad and balance-xor modes, bond_xdp_check() returns false when
xmit_hash_policy is vlan+srcmac, because the 802.1q payload is usually
absent due to hardware offload. This means a user can:
1. Attach a native XDP program to a bond in 802.3ad/balance-xor mode
with a compatible xmit_hash_policy (e.g. layer2+3).
2. Change xmit_hash_policy to vlan+srcmac while XDP remains loaded.
This leaves bond->xdp_prog set but bond_xdp_check() now returning false
for the same device. When the bond is later destroyed, dev_xdp_uninstall()
calls bond_xdp_set(dev, NULL, NULL) to remove the program, which hits
the bond_xdp_check() guard and returns -EOPNOTSUPP, triggering:
WARN_ON(dev_xdp_install(dev, mode, bpf_op, NULL, 0, NULL))
Fix this by rejecting xmit_hash_policy changes to vlan+srcmac when an
XDP program is loaded on a bond in 802.3ad or balance-xor mode.
commit 39a0876d595b ("net, bonding: Disallow vlan+srcmac with XDP")
introduced bond_xdp_check() which returns false for 802.3ad/balance-xor
modes when xmit_hash_policy is vlan+srcmac. The check was wired into
bond_xdp_set() to reject XDP attachment with an incompatible policy, but
the symmetric path -- preventing xmit_hash_policy from being changed to an
incompatible value after XDP is already loaded -- was left unguarded in
bond_option_xmit_hash_policy_set().
Note:
commit 094ee6017ea0 ("bonding: check xdp prog when set bond mode")
later added a similar guard to bond_option_mode_set(), but
bond_option_xmit_hash_policy_set() remained unprotected. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme: fix memory allocation in nvme_pr_read_keys()
nvme_pr_read_keys() takes num_keys from userspace and uses it to
calculate the allocation size for rse via struct_size(). The upper
limit is PR_KEYS_MAX (64K).
A malicious or buggy userspace can pass a large num_keys value that
results in a 4MB allocation attempt at most, causing a warning in
the page allocator when the order exceeds MAX_PAGE_ORDER.
To fix this, use kvzalloc() instead of kzalloc().
This bug has the same reasoning and fix with the patch below:
https://lore.kernel.org/linux-block/20251212013510.3576091-1-kartikey406@gmail.com/
Warning log:
WARNING: mm/page_alloc.c:5216 at __alloc_frozen_pages_noprof+0x5aa/0x2300 mm/page_alloc.c:5216, CPU#1: syz-executor117/272
Modules linked in:
CPU: 1 UID: 0 PID: 272 Comm: syz-executor117 Not tainted 6.19.0 #1 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:__alloc_frozen_pages_noprof+0x5aa/0x2300 mm/page_alloc.c:5216
Code: ff 83 bd a8 fe ff ff 0a 0f 86 69 fb ff ff 0f b6 1d f9 f9 c4 04 80 fb 01 0f 87 3b 76 30 ff 83 e3 01 75 09 c6 05 e4 f9 c4 04 01 <0f> 0b 48 c7 85 70 fe ff ff 00 00 00 00 e9 8f fd ff ff 31 c0 e9 0d
RSP: 0018:ffffc90000fcf450 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 1ffff920001f9ea0
RDX: 0000000000000000 RSI: 000000000000000b RDI: 0000000000040dc0
RBP: ffffc90000fcf648 R08: ffff88800b6c3380 R09: 0000000000000001
R10: ffffc90000fcf840 R11: ffff88807ffad280 R12: 0000000000000000
R13: 0000000000040dc0 R14: 0000000000000001 R15: ffffc90000fcf620
FS: 0000555565db33c0(0000) GS:ffff8880be26c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000002000000c CR3: 0000000003b72000 CR4: 00000000000006f0
Call Trace:
<TASK>
alloc_pages_mpol+0x236/0x4d0 mm/mempolicy.c:2486
alloc_frozen_pages_noprof+0x149/0x180 mm/mempolicy.c:2557
___kmalloc_large_node+0x10c/0x140 mm/slub.c:5598
__kmalloc_large_node_noprof+0x25/0xc0 mm/slub.c:5629
__do_kmalloc_node mm/slub.c:5645 [inline]
__kmalloc_noprof+0x483/0x6f0 mm/slub.c:5669
kmalloc_noprof include/linux/slab.h:961 [inline]
kzalloc_noprof include/linux/slab.h:1094 [inline]
nvme_pr_read_keys+0x8f/0x4c0 drivers/nvme/host/pr.c:245
blkdev_pr_read_keys block/ioctl.c:456 [inline]
blkdev_common_ioctl+0x1b71/0x29b0 block/ioctl.c:730
blkdev_ioctl+0x299/0x700 block/ioctl.c:786
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x1bf/0x220 fs/ioctl.c:583
x64_sys_call+0x1280/0x21b0 mnt/fuzznvme_1/fuzznvme/linux-build/v6.19/./arch/x86/include/generated/asm/syscalls_64.h:17
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x71/0x330 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7fb893d3108d
Code: 28 c3 e8 46 1e 00 00 66 0f 1f 44 00 00 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffff61f2f38 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007ffff61f3138 RCX: 00007fb893d3108d
RDX: 0000000020000040 RSI: 00000000c01070ce RDI: 0000000000000003
RBP: 0000000000000001 R08: 0000000000000000 R09: 00007ffff61f3138
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000001
R13: 00007ffff61f3128 R14: 00007fb893dae530 R15: 0000000000000001
</TASK> |
| In the Linux kernel, the following vulnerability has been resolved:
pmdomain: imx8m-blk-ctrl: fix out-of-range access of bc->domains
Fix out-of-range access of bc->domains in imx8m_blk_ctrl_remove(). |
| In the Linux kernel, the following vulnerability has been resolved:
arm64/fpsimd: signal: Fix restoration of SVE context
When SME is supported, Restoring SVE signal context can go wrong in a
few ways, including placing the task into an invalid state where the
kernel may read from out-of-bounds memory (and may potentially take a
fatal fault) and/or may kill the task with a SIGKILL.
(1) Restoring a context with SVE_SIG_FLAG_SM set can place the task into
an invalid state where SVCR.SM is set (and sve_state is non-NULL)
but TIF_SME is clear, consequently resuting in out-of-bounds memory
reads and/or killing the task with SIGKILL.
This can only occur in unusual (but legitimate) cases where the SVE
signal context has either been modified by userspace or was saved in
the context of another task (e.g. as with CRIU), as otherwise the
presence of an SVE signal context with SVE_SIG_FLAG_SM implies that
TIF_SME is already set.
While in this state, task_fpsimd_load() will NOT configure SMCR_ELx
(leaving some arbitrary value configured in hardware) before
restoring SVCR and attempting to restore the streaming mode SVE
registers from memory via sve_load_state(). As the value of
SMCR_ELx.LEN may be larger than the task's streaming SVE vector
length, this may read memory outside of the task's allocated
sve_state, reading unrelated data and/or triggering a fault.
While this can result in secrets being loaded into streaming SVE
registers, these values are never exposed. As TIF_SME is clear,
fpsimd_bind_task_to_cpu() will configure CPACR_ELx.SMEN to trap EL0
accesses to streaming mode SVE registers, so these cannot be
accessed directly at EL0. As fpsimd_save_user_state() verifies the
live vector length before saving (S)SVE state to memory, no secret
values can be saved back to memory (and hence cannot be observed via
ptrace, signals, etc).
When the live vector length doesn't match the expected vector length
for the task, fpsimd_save_user_state() will send a fatal SIGKILL
signal to the task. Hence the task may be killed after executing
userspace for some period of time.
(2) Restoring a context with SVE_SIG_FLAG_SM clear does not clear the
task's SVCR.SM. If SVCR.SM was set prior to restoring the context,
then the task will be left in streaming mode unexpectedly, and some
register state will be combined inconsistently, though the task will
be left in legitimate state from the kernel's PoV.
This can only occur in unusual (but legitimate) cases where ptrace
has been used to set SVCR.SM after entry to the sigreturn syscall,
as syscall entry clears SVCR.SM.
In these cases, the the provided SVE register data will be loaded
into the task's sve_state using the non-streaming SVE vector length
and the FPSIMD registers will be merged into this using the
streaming SVE vector length.
Fix (1) by setting TIF_SME when setting SVCR.SM. This also requires
ensuring that the task's sme_state has been allocated, but as this could
contain live ZA state, it should not be zeroed. Fix (2) by clearing
SVCR.SM when restoring a SVE signal context with SVE_SIG_FLAG_SM clear.
For consistency, I've pulled the manipulation of SVCR, TIF_SVE, TIF_SME,
and fp_type earlier, immediately after the allocation of
sve_state/sme_state, before the restore of the actual register state.
This makes it easier to ensure that these are always modified
consistently, even if a fault is taken while reading the register data
from the signal context. I do not expect any software to depend on the
exact state restored when a fault is taken while reading the context. |
| P-Net before 1.0.3 does not check that a complete block header is present in the received data before reading the next block in DCP Set and Identify requests. If the last block ends at the end of the receive buffer, the block length of the following block is read past the end of the buffer. In addition, a DCP Set block with a length smaller than the two-byte block qualifier makes the length underflow, so the block is processed with a length of 65534 bytes. This can cause a crash (denial of service) or disclose a small amount of memory content. Requires ADJACENT network access. |
| P-Net before 1.0.3 contains an integer underflow in pf_cpm_c_data_ind(). When handling a received cyclic data frame while the consumer is in the FRUN or RUN state, the offset of the APDU status was computed as the frame length minus 4 using 16-bit arithmetic, without checking that the frame is long enough. A crafted short frame makes the offset wrap around, so the function reads outside the receive buffer. This can cause a crash (denial of service) or disclose memory content. |
| P-Net before 1.0.3 does not validate the length of a received Ethernet frame in pf_eth_recv() before reading the EtherType, any VLAN tags and the PROFINET FrameID. The VLAN tag loop had no upper bound, so a truncated frame, or a frame consisting only of VLAN tags, makes the function read past the end of the receive buffer. This can cause a crash (denial of service) or disclose memory content. |
