| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| Linksys WAG200G through 1.01.06 contains an OS command injection vulnerability that allows authenticated attackers to execute commands by injecting backtick-delimited input into the timer_interval parameter. Attackers can send a crafted POST request to setup.cgi to start telnetd or download and run a backdoor, gaining full device control. |
| A flaw has been found in Linksys E5350 1.0.00.037. This impacts the function save_settings of the file /wizard/apply.cgi of the component Setup Wizard. Executing a manipulation of the argument wizard_router_pwd can lead to missing authentication. The attack may be launched remotely. The exploit has been published and may be used. The vendor was contacted early about this disclosure but did not respond in any way. |
| A vulnerability was detected in Linksys E5350 1.0.00.037. This affects the function system of the file /wizard/apply.cgi. Performing a manipulation of the argument ping_ip/traceroute_ip results in os command injection. The attack may be initiated remotely. The exploit is now public and may be used. The vendor was contacted early about this disclosure but did not respond in any way. |
| A security vulnerability has been detected in Linksys WRT54GL 4.30.18. The impacted element is the function system of the file apply.cgi of the component Traceroute Diagnostic Function. Such manipulation of the argument traceroute_ip leads to os command injection. The attack can be launched remotely. The exploit has been disclosed publicly and may be used. The vendor was contacted early about this disclosure but did not respond in any way. This vulnerability only affects products that are no longer supported by the maintainer. |
| A weakness has been identified in Linksys WRT54GL 4.30.18. The affected element is the function system of the file apply.cgi of the component Ping Diagnostic. This manipulation of the argument ping_ip causes os command injection. The attack can be initiated remotely. The exploit has been made available to the public and could be used for attacks. The vendor was contacted early about this disclosure but did not respond in any way. This vulnerability only affects products that are no longer supported by the maintainer. |
| Linksys WAG200G through 1.01.06 contains a stored cross-site scripting vulnerability that allows authenticated attackers to inject scripts via the policy_name parameter in setup.cgi. Attackers can save a malicious policy name from the AccessRes.htm page that executes in administrators' browsers when viewing the Status > Wireless page. |
| Linksys WAG200G through 1.01.06 contains a weak password change mechanism that allows attackers to change the administrator password without supplying the current password. Attackers with access to an authenticated administrator browser session can set a new password to lock out the legitimate administrator and take persistent device control. |
| SNMP service in Atmel 802.11b VNET-B Access Point 1.3 and earlier, as used in Netgear ME102 and Linksys WAP11, accepts arbitrary community strings with requested MIB modifications, which allows remote attackers to obtain sensitive information such as WEP keys, cause a denial of service, or gain access to the network. |
| Linksys EtherFast BEFN2PS4, BEFSR41, and BEFSR81 Routers, and possibly other products, allow remote attackers to gain sensitive information and cause a denial of service via an SNMP query for the default community string "public," which causes the router to change its configuration and send SNMP trap information back to the system that initiated the query. |
| An unauthenticated command injection vulnerability exists in the Start_EPI function of the httpd binary on Linksys E1200 v2 routers (Firmware E1200_v2.0.11.001_us.tar.gz). The vulnerability occurs because user-supplied CGI parameters (wl_ant, wl_ssid, wl_rate, ttcp_num, ttcp_ip, ttcp_size) are concatenated into system command strings without proper sanitization and executed via wl_exec_cmd. Successful exploitation allows remote attackers to execute arbitrary commands on the device without authentication. |
| The web interface on the Linksys WRT54g router with firmware 1.00.9 does not require credentials when invoking scripts, which allows remote attackers to perform arbitrary administrative actions via a direct request to (1) Advanced.tri, (2) AdvRoute.tri, (3) Basic.tri, (4) ctlog.tri, (5) ddns.tri, (6) dmz.tri, (7) factdefa.tri, (8) filter.tri, (9) fw.tri, (10) manage.tri, (11) ping.tri, (12) PortRange.tri, (13) ptrigger.tri, (14) qos.tri, (15) rstatus.tri, (16) tracert.tri, (17) vpn.tri, (18) WanMac.tri, (19) WBasic.tri, or (20) WFilter.tri. NOTE: the Security.tri vector is already covered by CVE-2006-5202. |
| Multiple cross-site request forgery (CSRF) vulnerabilities on the Cisco Linksys WAG54GS Wireless-G ADSL Gateway with 1.01.03 and earlier firmware allow remote attackers to perform actions as administrators via an arbitrary valid request to an administrative URI, as demonstrated by (1) a Restore Factory Defaults action using the mtenRestore parameter to setup.cgi and (2) creation of a user account using the sysname parameter to setup.cgi. |
| Cross-site request forgery (CSRF) vulnerability in apply.cgi in the Linksys WRT54GL Wireless-G Broadband Router with firmware 4.30.9 allows remote attackers to perform actions as administrators. |
| Cross-site scripting (XSS) vulnerability on the Linksys WRT300N router with firmware 2.00.20, when Mozilla Firefox or Apple Safari is used, allows remote attackers to inject arbitrary web script or HTML via the dyndns_domain parameter to the default URI. |
| Multiple cross-site scripting (XSS) vulnerabilities on the Cisco Linksys WAG54GS Wireless-G ADSL Gateway with 1.01.03 and earlier firmware allow remote attackers to inject arbitrary web script or HTML via unspecified vectors, a different issue than CVE-2007-3574. |
| The Cisco Linksys WAG54GS Wireless-G ADSL Gateway with 1.01.03 and earlier firmware has "admin" as its default password for the "admin" account, which makes it easier for remote attackers to obtain access. |
| The Linksys WRT54G router stores passwords and keys in cleartext in the Config.bin file, which might allow remote authenticated users to obtain sensitive information via an HTTP request for the top-level Config.bin URI. |
| Cross-site scripting (XSS) vulnerability in the Linksys SPA941 VoIP Phone with firmware 5.1.8 allows remote attackers to inject arbitrary web script or HTML via the From header in a SIP message. |
| Multiple cross-site scripting (XSS) vulnerabilities in setup.cgi on the Cisco Linksys WAG54GS Wireless-G ADSL Gateway with 1.00.06 firmware allow remote attackers to inject arbitrary web script or HTML via the (1) c4_trap_ip_, (2) devname, (3) snmp_getcomm, or (4) snmp_setcomm parameter. |
| The driver for the Linksys WRT350N Wi-Fi access point with firmware 2.00.17 on the Atheros AR5416-AC1E chipset does not properly parse the Atheros vendor-specific information element in an association request, which allows remote authenticated users to cause a denial of service (device reboot or hang) or possibly execute arbitrary code via an Atheros information element with an invalid length, as demonstrated by an element that is too long. |
